318ti.org forum (http://www.318ti.org/forum/index.php)
-   Engine (http://www.318ti.org/forum/forumdisplay.php?f=28)
-   -   ASC+T light diagnosis help (http://www.318ti.org/forum/showthread.php?t=36573)

Apittma 06-29-2012 06:32 PM

ASC+T light diagnosis help
 
Hi everyone. I'm a new owner of a '98 base model with asc, and the dash indicator light comes on and stays on within the first mile or so of driving each time I start the car. Before this point, it does respond to the switch. Searching on here and bfc seems to indicate that the system usually malfunctions with the abs since they use the same wheel speed sensors. However, my abs is functioning properly. I've already disconnected and cleaned the electrical connectors at the asc cable motor along the right side of the engine bay and the asc intake valve. I also checked the relay for corrosion (though i have not checked any of these for function... Haven't had the chance yet, and can't find my multimeter). The cable is seated properly in the semi-sircular pully at the intake side. I know many people will suggest having the abs computer scanned, but I don't really have that cash to fork over when I'm not so sure it's gonna give any result, since the abs is functioning properly. I'm kind of at a loss, and would appreciate any help. Thanks!

1996 328ti 06-29-2012 08:20 PM

Is the throttle cable in the correct position? I've seen them pop off. <I think>

Apittma 06-29-2012 10:17 PM

Quote:

Originally Posted by 1996 328ti (Post 333182)
Is the throttle cable in the correct position? I've seen them pop off. <I think>

It's in the correct position, I'm afraid...

Apittma 06-29-2012 10:22 PM

Additionally, I tried to check the relay by pushing the asc+t switch before moving the car (so the light had not come on yet), and there was no clicking actuation in the relay. However, I'm not entirely sure that hitting the switch should activate the relay, so I may not actually be testing anything *facepalm*. Can anyone clarify this? Thanks again!

Apittma 07-02-2012 02:09 AM

Update
 
I took the secondary throttle body out of the engine bay today, and attempted to remove and check the secondary throttle position sensor. I was unable to get the sensor off because one of the attaching screws was so stinkin' locked up (and already stripped out), so I doused it in penetrating oil. I had to run an errand, so I went ahead and put it back in the car, and it seems to be working again, rather inexplicably. Hopefully, the problem won't resurface! If so, I'll bring it back to this thread.

pdxmotorhead 07-02-2012 02:48 AM

Carbon buildup most likely, I flush the throttle body with carb cleaner and lube at each oil change.


Dave

Apittma 09-07-2012 07:55 PM

Well, the problem is back... The ASC+t light's still coming on after a short period of time on the road, and the ABS still functions just fine with no warning light. I've tried playing around with everything again, and can't seem to find the problem. If I continue having trouble with it, I'm probably gonna go ahead and do the secondary throttle delete. There's no point in unnecessarily having added airflow resistance for a non-functioning stability control system.

drummond07 09-10-2012 12:38 AM

Quote:

Originally Posted by Apittma (Post 338119)
Well, the problem is back... The ASC+t light's still coming on after a short period of time on the road, and the ABS still functions just fine with no warning light. I've tried playing around with everything again, and can't seem to find the problem. If I continue having trouble with it, I'm probably gonna go ahead and do the secondary throttle delete. There's no point in unnecessarily having added airflow resistance for a non-functioning stability control system.

Hi Apittma,

have you figured anything out with this issue? I'm looking at a car that has this light and the ABS light on and I'm wondering if this is a major issue to fix or an easy one. Thanks for you help.

Apittma 09-11-2012 05:17 AM

Quote:

Originally Posted by drummond07 (Post 338194)
Hi Apittma,

have you figured anything out with this issue? I'm looking at a car that has this light and the ABS light on and I'm wondering if this is a major issue to fix or an easy one. Thanks for you help.

Hi Drummond,

Sorry about taking so long to reply. I've just been swamped! I have good and bad news for you. The good news is that the problem you're experiencing is much more common than my problem, so there's a lot more information out there about how to deal with it. Though there's a lot of bad blood over there, check out bimmerforums.com. You can do a search for "asc abs" in the e36 forum, and should get a good selection of results. The bad news is that, from what I've read, it could be one a few things (though none are especially costly), and it takes a bit of work to figure out exactly what's going on. It could be something extremely simple, like a loose/poor connection at the asc actuator along the driver's side of the engine bay. It could also be one of the wheel speed sensors for the abs. If one of these stops working, it interferes with both the abs and the asc. Again, bf.c should be able to help you sort it out! Sorry for the quazi-convoluted answer, but I hope this will get you started in the right direction. Good luck with your purchase!

drummond07 09-11-2012 01:50 PM

Thanks for the response and info. I am a member of the bimmerforums as I research issues on my 99 M3 convert. from time to time. I will check it out for the 318Ti issues.

Monolith 09-12-2012 06:50 PM

To the OP, something to try:

There is a mechanical error code associated also with the ASC+T light. You'll need an INPA interface to read the code. When this code occurs, the ASC+T light on the dash cannot be reset by the ASC switch. The light remains on as long as the code is detected. It can seem intermittent.

The code is set when the cable link is tested by the system. Replacing the actuator (unless there is damage to it) generally won't fix the problem. Make sure your actuator rotates freely.

Does the cable have slack in the end? If so, tighten up the cable end one or two turns to take up some cable slack. See if the code comes back. If it comes back, tighten the cable one or two turns more. See if the code comes back.

In my case, the cable was just a little too loose and when the system tested the actuator, it did not feel enough resistance and assumed the cable was not operational. Don't over tighten it.

jenkinskg 08-25-2014 09:21 PM

I have a 97 that start giving same symtoms as above.
ABS works 100%
ASC goes sometimes for many miles before light comes on.
Restart car and its off again.

I have a few ways to read codes , what exactly will read this error?
I need the asc to survive the winter

drummond07 08-26-2014 01:45 AM

Quote:

Originally Posted by jenkinskg (Post 365622)
I have a 97 that start giving same symtoms as above.
ABS works 100%
ASC goes sometimes for many miles before light comes on.
Restart car and its off again.

I have a few ways to read codes , what exactly will read this error?
I need the asc to survive the winter

It is my understanding that the codes can only be read and removed by the dealer. I have a couple OBD II readers and neither will read the codes. After replacing all the ABS sensors it was diagnosed that the control unit was faulty. You can not buy new anymore (according toy dealer) and I have not found anyone who will repair. I think the best option is a recycle (junk) yard. Personally I'm glad it doesn't function as it made it more difficult to get moving in deep snow and on hard pack (MN winters). Good luck. Sorry yet answer wasn't what you wanted.

jenkinskg 09-16-2014 07:55 PM

asc light
 
New development, it is off for good now.
Thought it finally got fixed or resolved itself, now I realize holding button does not turn it on.
I also notice light not turned on during startup.

Looks like since buld was on almost all the time, bulb is out now.
I really do want it to function during the winter, it helps a lot on slippery roads.
If I want it off, can be turned off in a sec.
If it broken cannot use it at all

Going to get code read and resolve it

Hotredti 11-13-2017 06:55 AM

FIXED!!!!!!!!
 
Adjusting the actuator cable of the ASC butterfly is what fixed my problem. Thank You!!!


Quote:

Originally Posted by Monolith (Post 338352)
To the OP, something to try:

There is a mechanical error code associated also with the ASC+T light. You'll need an INPA interface to read the code. When this code occurs, the ASC+T light on the dash cannot be reset by the ASC switch. The light remains on as long as the code is detected. It can seem intermittent.

The code is set when the cable link is tested by the system. Replacing the actuator (unless there is damage to it) generally won't fix the problem. Make sure your actuator rotates freely.

Does the cable have slack in the end? If so, tighten up the cable end one or two turns to take up some cable slack. See if the code comes back. If it comes back, tighten the cable one or two turns more. See if the code comes back.

In my case, the cable was just a little too loose and when the system tested the actuator, it did not feel enough resistance and assumed the cable was not operational. Don't over tighten it.



All times are GMT +1. The time now is 08:47 PM.

vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org