Forum: Maintenance 04-10-2016, 06:56 PM |
Replies: 6 Views: 3,998 |
Forum: Engine Swaps 03-28-2016, 06:38 AM |
Replies: 12 Views: 4,685 |
Forum: Parting out & Parts (US) 03-25-2016, 07:01 AM |
Replies: 7 Views: 4,716 |
Forum: Engine Swaps 03-25-2016, 06:59 AM |
Replies: 12 Views: 4,685 Its very very common to do a OBD1 conversion on... Its very very common to do a OBD1 conversion on S52's because of tuning. Especially where emission testng is lax or non existent. In my state you'd have to have the cat and pre/post sensors in place... |
Forum: Wheels and Tires 03-25-2016, 06:53 AM |
Replies: 79 Views: 33,150 Kumho Ecsta V710 are good tires, not as quite... Kumho Ecsta V710 are good tires, not as quite good as some but they last and are very tough. I had a client road race an S12 Turbo nissan on them and they were a really good value. S12 has very... |
Forum: Engine 03-25-2016, 06:40 AM |
Replies: 9 Views: 3,559 |
Forum: Engine Swaps 03-25-2016, 06:21 AM |
Replies: 12 Views: 4,685 |
Forum: Maintenance 03-25-2016, 06:18 AM |
Replies: 2 Views: 8,216 Factory spec was 10w140 in cold climates and... Factory spec was 10w140 in cold climates and 20w50 in warmer climates if I recall, I know mine hates the new light oil get noisy. I use Rotella T6 price is right and the viscosity is available in it. |
Forum: Engine 03-25-2016, 06:10 AM |
Replies: 9 Views: 3,559 |
Forum: Maintenance 03-24-2016, 07:04 AM |
Replies: 2 Views: 1,956 First remove and inspect the host from the Air... First remove and inspect the host from the Air Flow sensor to the throttle body, they get old and get cracks on the bottom side that don't show up easily till you take it out and look and flex it.... |
Forum: Engine 02-15-2016, 09:15 AM |
Replies: 4 Views: 2,851 |
Forum: Lounge 02-15-2016, 09:11 AM |
Replies: 20 Views: 15,110 The Nissan Z cars ran an almost identical rear... The Nissan Z cars ran an almost identical rear suspension setup as ours for a long time.. The M3 had the same suspension in some of its most dominant race years. Ours doesn't break with a mild... |
Forum: Electrical 04-03-2015, 06:10 AM |
Replies: 18 Views: 5,234 |
Forum: Engine 04-02-2015, 05:18 AM |
Replies: 24 Views: 7,738 Johns got the most time on boost.. :D I've... Johns got the most time on boost.. :D I've never built a engine and regretted the forged rods, I have built one without and regretted it.. It depends on the quality you start with. To control... |
Forum: Engine 04-02-2015, 04:21 AM |
Replies: 5 Views: 2,139 |
Forum: Engine 04-02-2015, 04:18 AM |
Replies: 24 Views: 7,738 Oil will also "fix" the low compression in the... Oil will also "fix" the low compression in the gasket as well if its not blown all the way. Leakdown is your friend compression tests are pretty low info. Pump each cylinder up and see if you have... |
Forum: Engine 04-02-2015, 04:15 AM |
Replies: 1 Views: 1,293 |
Forum: Engine Swaps 02-01-2015, 08:10 PM |
Replies: 23 Views: 5,340 Go standalone and never look back. ?? SDS,... Go standalone and never look back. ?? SDS, Megasquirt, Apexi... there are many starting at about 1000 and going up.. You've likely got a mismatch ecu to car (Auto vs manual??) Possibly a wiring... |
Forum: Lounge 02-01-2015, 07:21 PM |
Replies: 1 Views: 1,646 Upper Radiator hose bib let go. Well it finally happened,, popped the upper hose bib on the radiator. Luckily I was headed up an on ramp heard a noise like a champagne cork and saw steam in the rear view.. Killed the motor and... |
Forum: Suspension 02-01-2015, 07:10 PM |
Replies: 7 Views: 6,540 |
Forum: General Chit Chat 01-13-2015, 05:53 AM |
Replies: 9 Views: 2,480 |
Forum: Electrical 12-07-2014, 01:33 AM |
Replies: 4 Views: 2,011 Great batteries wont leak. DO NOT USE A... Great batteries wont leak. DO NOT USE A TRICKLE/float CHARGER ON THEM! It will kill them. They like being charged by the cars charging system, they dont like being deep cycled, if you run... |
Forum: Cars for Sale 12-07-2014, 01:29 AM |
Replies: 5 Views: 4,112 |
Forum: Interior and ICE 11-27-2014, 07:30 AM |
Replies: 3 Views: 1,699 |
Forum: Parting out & Parts (US) 11-22-2014, 10:27 PM |
Replies: 55 Views: 23,088 Hmm, it would be WAY easier to source a used... Hmm, it would be WAY easier to source a used 318is motor and replace yours. Way less work than a part-out.. Of course the average TI is not going to be worth much over about 3000 these days.. Sad but... |