318ti.org forum

Go Back   318ti.org forum > Search Forums

Notices

.
Showing results 1 to 11 of 11
Search took 0.00 seconds.
Search: Posts Made By: Fluxcapacitor
Forum: Induction 07-10-2015, 05:22 PM
Replies: 54
Views: 20,226
Posted By Fluxcapacitor
Johnboy! long time no talk! (I tried e-mailing a...

Johnboy! long time no talk! (I tried e-mailing a while back but your old rr e-mail doesn't work anymore). Sorry to hear you sold your car! (I'm betting it put out the most HP of any 4 cylinder 318ti...
Forum: Cars for Sale 07-10-2015, 05:00 PM
Replies: 6
Views: 4,216
Posted By Fluxcapacitor
Hi, I had the DASC (completely) rebuilt twice;...

Hi, I had the DASC (completely) rebuilt twice; first by a guy iwho did a lousey job (hardly any difference in pressure & his new nose seal started leaking!) so then I sent it out to the airplane...
Forum: Cars for Sale 07-10-2015, 04:18 PM
Replies: 6
Views: 4,216
Posted By Fluxcapacitor
pics

Edit: Sorry guys, I still haven't been able to get pics into the post (It won't take a dropbox link for some reason and it crashes when I try to upload images into an album too)

Here's a few...
Forum: Cars for Sale 07-09-2015, 07:19 PM
Replies: 6
Views: 4,216
Posted By Fluxcapacitor
1998 Black Msport 5spd 318ti $5,100

SOLD to the gentleman just north of Boston! :)


a few dropbox links in the mean time

https://www.dropbox.com/s/76e3av1ey8bvwui/318tiFrontAngle.jpg?dl=0
...
Forum: Induction 07-08-2015, 09:25 PM
Replies: 54
Views: 20,226
Posted By Fluxcapacitor
Great to see you fixed the idle! :) Re exhaust; I...

Great to see you fixed the idle! :) Re exhaust; I had a nice sounding supersprint muffler that sounded good on a stock engine, but then after an engine replacement w/ the higher flowing MM engine,...
Forum: Induction 07-01-2015, 06:59 PM
Replies: 54
Views: 20,226
Posted By Fluxcapacitor
Were you able to fix idle? The rrfp shouldn't be...

Were you able to fix idle? The rrfp shouldn't be holding pressure for more than a fraction of a sec. It's not impossible, but it would need a "springy" volume of gas combined w/ a restriction (like...
Forum: Induction 05-28-2015, 09:11 PM
Replies: 54
Views: 20,226
Posted By Fluxcapacitor
Re rrfpr, yours is different from the dasc one &...

Re rrfpr, yours is different from the dasc one & the only thing I can remember about the dasc one is that it had an air pressure fitting that went to the boost side of the supercharger & then it had...
Forum: Induction 05-28-2015, 01:18 AM
Replies: 54
Views: 20,226
Posted By Fluxcapacitor
Re rough idle, I'd check for vacuum leaks foist...

Re rough idle, I'd check for vacuum leaks foist (spray brake cleaner near potential leaks to see if it speeds up?) & then take off the idle valve & spray brake cleaner through it to make sure it...
Forum: Induction 05-28-2015, 01:06 AM
Replies: 54
Views: 20,226
Posted By Fluxcapacitor
Oh! stock fuel pump is fine for well over 300 hp....

Oh! stock fuel pump is fine for well over 300 hp. All the stock replacement pumps for the 318 are rated for over 45 gph. (Gas is a little over 7 lbs/gallon, so 45X7 = 315 lb/hr)
Even if you went up...
Forum: Induction 05-12-2015, 04:02 PM
Replies: 54
Views: 20,226
Posted By Fluxcapacitor
Oops, I read too fast; you're using the rising...

Oops, I read too fast; you're using the rising rate fuel pressure (from a stage 1 DA SC kit?) That will increase pressure under boost and get more out of your 20lb injectors. The stage 3 kit if I...
Forum: Induction 05-11-2015, 11:54 PM
Replies: 54
Views: 20,226
Posted By Fluxcapacitor
Great write-up! If I ever go to a bigger...

Great write-up! If I ever go to a bigger supercharger I'll be pouring over your pictures for ideas! :) I had no problem going to a light weight flywheel (lower rotational mass helps acceleration)....
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT +1. The time now is 01:28 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
[page compression: 47.90 k/54.84 k (12.65%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.