318ti.org forum

Go Back   318ti.org forum > Search Forums
Reload this Page Search Results
Register FAQ Donate Calendar Search Today's Posts Mark Forums Read

Notices

.
Showing results 1 to 11 of 11
Search took 0.00 seconds. Search: Posts Made By: Peugeot
Forum: Lounge 06-30-2019, 06:08 PM
Replies: 2
Views: 2,928
Posted By Peugeot
Thoughts about my ti

Hey all, I have to again, thank the organizers of this site as it's been my go-to site for almost a decade on all things ti. I have owned my car that long. A 96 ti, silver/gray 5sp with 331K It...
Forum: Maintenance 07-25-2014, 01:50 AM
Replies: 171
Views: 137,665
Posted By Peugeot
Just did this job myself. Same as marslc1 except...

Just did this job myself. Same as marslc1 except I didn't replace hose clamps. I cleaned every clamp and bolt thoroughly. A few things I learned and should share.

I was quoted $2,700 for this...
Forum: Engine 07-25-2014, 01:26 AM
Replies: 6
Views: 2,378
Posted By Peugeot
Update: Followed advice given and all worked...

Update: Followed advice given and all worked perfectly. Only place you need FIPG is at the half moons in the back on the valve cover gasket. Don't over-do it, but put a thin film with your finger...
Forum: Engine 07-17-2014, 02:45 AM
Replies: 6
Views: 2,378
Posted By Peugeot
Thanks for the voice of experience there. I'm...

Thanks for the voice of experience there. I'm sure it'll be good. Can't wait 'till I finish. Wish I didn't work so slow!
Forum: Engine 07-16-2014, 03:03 AM
Replies: 6
Views: 2,378
Posted By Peugeot
Cooling system rebuild - Form-in-place gasket points

Hi all,

Tackling this little nasty job. I didn't know such a well running car could get so nasty dirty. Valve cover gasket let go too. Rad was shot, so it was time to do the full cooling system...
Forum: Transmission 01-20-2013, 06:45 PM
Replies: 3
Views: 1,038
Posted By Peugeot
Hey, thanks guys. Car is quite old, but runs so...

Hey, thanks guys. Car is quite old, but runs so well, I have to fix it! Thanks for the info.
Forum: Parting out & Parts (US) 01-20-2013, 04:13 AM
Replies: 5
Transmission Getrag 250
Views: 2,610
Posted By Peugeot
Hi Chris, I've never shipped or received a...

Hi Chris,

I've never shipped or received a transmission before. How much to ship to 98136?
Forum: Transmission 01-20-2013, 12:00 AM
Replies: 3
Views: 1,038
Posted By Peugeot
G250 from a Z3

Hi all,

My 5-speed tranny needs to be opened up and the first gear syncho replaced. Shops want a fair amount of $$$ to do this. However, I've got an opportunity to buy a low-mileage 5-speed out...
Forum: US and North America 02-02-2011, 03:14 AM
Replies: 43
Views: 6,731
Posted By Peugeot
Don't post much 'cause my ti never needs anything...

Don't post much 'cause my ti never needs anything - 280,000 miles and runs like a swiss watch! :) So, I can't PM (need 5 more posts).

Anyway, I do need rear wiper motor. I live in Seattle so I...
Forum: Interior and ICE 12-05-2010, 02:17 AM
Replies: 1
Views: 1,127
Posted By Peugeot
Cellphone/smartphone mount

Post your solutions. I've exhausted my Search-Fu and have failed to come up with something.

ProClip (www.proclip.com) like all the others don't seem to recognize the unique dash layout of the ti.
Forum: Maintenance 02-26-2010, 11:58 PM
Replies: 5
Views: 1,371
Posted By Peugeot
Intro & maintenance questions

Hi all,

I bought my first BMW in November. A 1996 5 speed.

It's got 274K on the clock but could easily pass for 74.

I turn my own wrench usually and I need to get an oil change in.
...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT +1. The time now is 03:02 AM.

Donate - Contact Us - www.318ti.org - Archive - Top

.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
[page compression: 46.10 k/52.57 k (12.29%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.