Forum: Engine Swaps 03-13-2019, 09:27 PM |
Replies: 2 Views: 4,938 |
Forum: Knowledge Base 10-29-2016, 01:43 AM |
Replies: 5 Views: 15,146 How I got this sucker out Had to replace lower joint because one axis was seizing up, and when I got it unbolted the thing didn't want to come out. So I bathed it in PB Blaster and tried getting it out with a couple of pry... |
Forum: Suspension 03-09-2016, 11:42 AM |
Replies: 2 Views: 2,121 |
Forum: Suspension 03-08-2016, 08:48 PM |
Replies: 2 Views: 2,121 Power steering rack Hello folks! I just bought a used power steering rack and it's obviously not in the straight position. How can you tell when it is? I would like to install this with minimal headache! TIA |
Forum: Parting out & Parts (US) 01-23-2016, 11:34 PM |
Replies: 46 Views: 16,886 |
Forum: Parting out & Parts (US) 01-23-2016, 02:33 AM |
Replies: 46 Views: 16,886 Has anyone else bought from him? If not, a... Has anyone else bought from him? If not, a warning not to buy from him. I'm out some money with this guy so far since the beginning of December. Luckily it's not a sum that I could ill afford to... |
Forum: Parting out & Parts (US) 12-01-2015, 01:01 AM |
Replies: 46 Views: 16,886 |
Forum: Misc 11-13-2015, 07:13 PM |
Replies: 0 Views: 6,816 Crossmember bolts I'm planning on fixing an oil pan leak on my ti, and as I understand it the crossmember bolts are one time use only. Has anyone here ever tried reusing them? I'm considering replacing them with grade... |
Forum: Suspension 06-08-2014, 03:17 PM |
Replies: 16 Views: 3,518 Now if only I could weld... thanks Cirrus,... Now if only I could weld... thanks Cirrus, because I did see a lot of mud up in there which is why I thought it was due to the trip in the farmer's field. Is the design different with the... |
Forum: Lounge 06-07-2014, 02:03 PM |
Replies: 316 Views: 198,597 |
Forum: Suspension 06-07-2014, 01:56 PM |
Replies: 16 Views: 3,518 @blackbmw: I hate to see them go myself,... @blackbmw: I hate to see them go myself, especially when my insurance company tried to total mine two years for pretty much all cosmetic damage! @mtlblue replaced every bushing except the... |
Forum: Suspension 06-07-2014, 12:32 AM |
Replies: 16 Views: 3,518 |
Forum: Suspension 06-06-2014, 07:52 PM |
Replies: 16 Views: 3,518 |
Forum: Suspension 06-06-2014, 06:56 PM |
Replies: 16 Views: 3,518 Yeah, I think it happened only because an idiot... Yeah, I think it happened only because an idiot in a truck was coming around the same curve I was in, only he was doing it sideways in the rain. I had to bail into a farmer's field to avoid worse.... |
Forum: Suspension 06-06-2014, 05:55 PM |
Replies: 16 Views: 3,518 Just how boned is my ti? Just getting ready to change brakes when I found this. This only could have happened when I avoided a stupid yayhoo driving like an idiot in the rain last October. But it has been through an... |
Forum: Maintenance 06-23-2013, 07:13 AM |
Replies: 6 Views: 2,267 I have a hydraulic press myself, but I am not... I have a hydraulic press myself, but I am not sure how to go about putting the whole assembly in there to press the hub in, as there is no room to pass the axle shaft between the support beams. I... |
Forum: Maintenance 06-21-2013, 05:47 AM |
Replies: 6 Views: 2,267 |
Forum: Parting out & Parts (US) 04-12-2013, 05:20 PM |
Replies: 21 Views: 6,830 |
Forum: Suspension 03-21-2013, 04:18 PM |
Replies: 5 Views: 1,707 Nope, no flats, which was why I found it... Nope, no flats, which was why I found it particularly sucky that the OEM chose to make the change that they did. I was ready for the hex key setup but when even that wasn't there I looked for flats... |
Forum: Suspension 03-20-2013, 07:22 PM |
Replies: 5 Views: 1,707 |
Forum: Suspension 03-20-2013, 07:12 AM |
Replies: 5 Views: 1,707 Tie rod end help Hello guys, I bought some Lemfoerder tie rod ends to replace the originals, but where the originals had the 5mm Allen wrench hole, the new ones seem to just have a dimple in the center. Now my tie... |
Forum: Engine 06-02-2012, 06:26 PM |
Replies: 6 Views: 3,314 |
Forum: Engine Swaps 05-03-2012, 09:32 AM |
Replies: 226 Views: 124,322 Jim, Got ready to do my swap about four... Jim, Got ready to do my swap about four years ago, but life as usual got in the way. I wanted to ask you a couple of questions: 1. Have there been any major changes in your manual since then,... |
Forum: US and North America 01-29-2012, 11:21 AM |
Replies: 0 Views: 1,306 WTB: Complete set of black door speakers (OEM) Getting ready to install door speakers from bavsound.com but I need the OEM speaker mounts so that I can gut them and put the new speakers in. Would like to have them in the best possible condition.... |
Forum: Maintenance 09-29-2011, 03:36 PM |
Replies: 29 Views: 12,411 |