318ti.org forum

Go Back   318ti.org forum > Search Forums

Notices

.
Showing results 1 to 25 of 201
Search took 0.04 seconds.
Search: Posts Made By: andakn
Forum: General Chit Chat 09-12-2018, 08:42 PM
Replies: 189
Views: 91,854
Posted By andakn
I've worked out most of the ECU settings now just...

I've worked out most of the ECU settings now just teaching myself how to tune. I've had a little experience with it but not creating all maps and settings from scratch. As for the turbo, it is...
Forum: General Chit Chat 09-11-2018, 06:59 PM
Replies: 189
Views: 91,854
Posted By andakn
I think the Ebay turbo went out. Started smoking...

I think the Ebay turbo went out. Started smoking bad last night and didn't seem to clear out. I'm going to do some more checking tonight, I'm hopeful that it was just some that leaked into the...
Forum: General Chit Chat 09-08-2018, 04:13 PM
Replies: 189
Views: 91,854
Posted By andakn
Haltech is really the only standalone unit I have...

Haltech is really the only standalone unit I have any real experience with, looked into megasquirt but didn't feel comfortable building it and my circuit board soldering skills are not great. I've...
Forum: General Chit Chat 09-06-2018, 01:22 AM
Replies: 189
Views: 91,854
Posted By andakn
Link to the latest video. ...

Link to the latest video.
https://youtu.be/AdkrnxP7DN0
Forum: General Chit Chat 09-04-2018, 04:55 PM
Replies: 189
Views: 91,854
Posted By andakn
Maybe I'll do a walk around video tonight on...

Maybe I'll do a walk around video tonight on where I'm at and how I hooked stuff up. I have the stock computer wired in so my ews and factory alarm still operates like stock.
Forum: General Chit Chat 09-03-2018, 06:01 PM
Replies: 189
Views: 91,854
Posted By andakn
Well it's running, I had some issues but slowly...

Well it's running, I had some issues but slowly sorting them out. Found that the stock coil was going out and with the higher power ignition system it was sparking out the side of the coil to the...
Forum: General Chit Chat 08-31-2018, 06:58 PM
Replies: 189
Views: 91,854
Posted By andakn
I hit the limits of the piggy back ECU at around...

I hit the limits of the piggy back ECU at around 650hp and 21psi boost. Rather than keep messing with it I decided to go ahead and bite the bullet and install the haltech elite 1500. It will kinda...
Forum: General Chit Chat 08-31-2018, 02:26 PM
Replies: 189
Views: 91,854
Posted By andakn
Started wiring in the standalone ECU and hope to...

Started wiring in the standalone ECU and hope to have it running again this weekend. Also installing the duel 340lph flex fuel pumps and also adding the flex fuel sensor.
Forum: Engine 08-03-2018, 05:25 PM
Replies: 4
Views: 429
Posted By andakn
Most of the time done when doing head gasket,...

Most of the time done when doing head gasket, when I send a head to the machine shop I give them those with it and they replace them while machining the head. To do them on the car is nearly...
Forum: Engine 08-03-2018, 05:16 PM
Replies: 4
Views: 429
Posted By andakn
Valve guide seals

Valve guide seals
Forum: General Chit Chat 08-02-2018, 11:51 PM
Replies: 189
Views: 91,854
Posted By andakn
Driveshaft is in with the new motor mounts and...

Driveshaft is in with the new motor mounts and also I installed a kevlar transmission blanket. Also with the new injectors I went back to the 10psi pulley, so know its 10psi right off the line and by...
Forum: United States 08-01-2018, 10:00 PM
Replies: 31
Views: 4,176
Posted By andakn
These are the solid mounts I'm running, no metal...

These are the solid mounts I'm running, no metal to metal contact, so they are a lot less noisy. But still some, they are by silver project and I picked them up on ebay
Forum: General Chit Chat 07-23-2018, 02:26 AM
Replies: 189
Views: 91,854
Posted By andakn
I guess this will be my rough draft, I'm thinking...

I guess this will be my rough draft, I'm thinking I need to build a tube steel subframe or maybe just a better box steel design. I'd really like to make one that comes all the way around behind the...
Forum: General Chit Chat 07-22-2018, 08:30 PM
Replies: 189
Views: 91,854
Posted By andakn
Started modifying the subframe to fit the adapter...

Started modifying the subframe to fit the adapter flange and larger u joint. Clears everything else, but is kinda close to the center carrier support bracket so I'll be cutting that out too. Good...
Forum: General Chit Chat 07-16-2018, 03:48 PM
Replies: 189
Views: 91,854
Posted By andakn
I have to clearance a few items and possibly may...

I have to clearance a few items and possibly may be switching to a fuel cell. I ran out of gas for the welder this weekend, and my air compressor is down. Hope to get back on it tonight, also have a...
Forum: General Chit Chat 07-14-2018, 04:55 PM
Replies: 189
Views: 91,854
Posted By andakn
New driveshaft vs old

New driveshaft vs old
Forum: General Chit Chat 07-13-2018, 09:37 PM
Replies: 189
Views: 91,854
Posted By andakn
It came!!! Can't wait to put it in and get back...

It came!!! Can't wait to put it in and get back to the track.
Forum: General Chit Chat 05-18-2018, 02:18 PM
Replies: 189
Views: 91,854
Posted By andakn
I like these mounts because even if the urethane...

I like these mounts because even if the urethane rips they will not come completely apart, and with the carbon fiber driveshaft if the motor moves too much it will damage the shaft. And I am almost...
Forum: General Chit Chat 05-17-2018, 05:27 PM
Replies: 189
Views: 91,854
Posted By andakn
Ordered motor mounts from the same company as my...

Ordered motor mounts from the same company as my trans mounts
Forum: General Chit Chat 05-11-2018, 04:01 PM
Replies: 189
Views: 91,854
Posted By andakn
It's kinda good that I have to wait. I've been...

It's kinda good that I have to wait. I've been neglecting my Camaro constantly working on the black car so, I divided my time between the 2. Weekends are for the camaro and weeknights are for the...
Forum: General Chit Chat 05-11-2018, 03:33 PM
Replies: 189
Views: 91,854
Posted By andakn
Ended up ordering the carbon fiber driveshaft,...

Ended up ordering the carbon fiber driveshaft, the shaft is too long to use chrome moly for the power and speed I'm going for. Downside is, it's the peak of racing season and there is a 5-7 week wait...
Forum: Lounge 05-08-2018, 06:26 PM
Replies: 74
Views: 24,058
Posted By andakn
I get about 8-12 in my black car. It spends most...

I get about 8-12 in my black car. It spends most of the time at full throttle. And with 1200cc injectors I can empty a tank real quick
Forum: Engine 05-04-2018, 02:23 PM
Replies: 3
Views: 2,083
Posted By andakn
Could I get the xdf file I paid for over a year...

Could I get the xdf file I paid for over a year ago? I've emailed several times with no response.
Forum: General Chit Chat 04-23-2018, 04:38 PM
Replies: 189
Views: 91,854
Posted By andakn
https://youtu.be/wevyyfI9HEE Video of...

https://youtu.be/wevyyfI9HEE
Video of yesterday's autocross event. I'm going with the chrome moly shaft from the driveshaft shop. Not sure when I'll start the ECU change, still need a few parts for...
Forum: General Chit Chat 04-21-2018, 11:15 PM
Replies: 189
Views: 91,854
Posted By andakn
I'm waiting on the new driveshaft but I have most...

I'm waiting on the new driveshaft but I have most of my new ECU stuff. Haltech 1500, HPI4 ignition, flex fuel sensor, multi fuel 1200cc injectors and twin 340lph fuel pumps. Also in light of the...
Showing results 1 to 25 of 201

 
Forum Jump

All times are GMT +1. The time now is 07:33 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2018, 318ti.org
[page compression: 71.18 k/80.00 k (11.03%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.