318ti.org forum

Go Back   318ti.org forum > Search Forums
Reload this Page Search Results
Register FAQ Donate Calendar Today's Posts Search

Notices

.
Showing results 1 to 12 of 12
Search took 0.00 seconds. Search: Posts Made By: gringoti
Forum: Wheels and Tires 01-05-2014, 05:19 AM
Replies: 10
Views: 2,685
Posted By gringoti
I use 8" 38mm offset rims with 15mm spacers (on...

I use 8" 38mm offset rims with 15mm spacers (on rear) and 225s and have no issues.
Forum: Engine 07-22-2013, 12:27 AM
Replies: 3
Views: 880
Posted By gringoti
It does look rotten and previously repaired with...

It does look rotten and previously repaired with goop of some kind. Thnx. Will replace that.
Forum: Engine 07-21-2013, 07:22 PM
Replies: 3
Views: 880
Posted By gringoti
Hesitation with hiss sound

I get a momentary hesitation accompanied by a short hissing sound like a pop off valve. No turbo though! :) This happens every 20 seconds or so, more under load or engine braking going downhill....
Forum: Suspension 07-13-2013, 08:47 PM
Replies: 26
Views: 17,584
Posted By gringoti
sliding bushings over swaybars??

i thought i had answered my own question about this but i think the bushings are not in fact split and have to be slid over and along the sway bars to the correct position. The urethane PowerFlex...
Forum: Suspension 07-03-2013, 07:03 AM
Replies: 26
Views: 17,584
Posted By gringoti
I see looking at pictures of the bushings that...

I see looking at pictures of the bushings that they split to go around the sway bar. Also that the mount should have a stud coming out of it and a nut holds the bracket/clamp over the bushing.
I do...
Forum: Suspension 07-02-2013, 10:37 PM
Replies: 26
Views: 17,584
Posted By gringoti
Bushings

And how do you get new rubber or urethane bushings on the Sway Bar over the big tabs on the ends of the sway bar? Thanks!
Forum: Suspension 07-02-2013, 04:22 PM
Replies: 26
Views: 17,584
Posted By gringoti
Welding

After a couple of tack welds I would remove the bushing clamp and do a proper weld of the support to the frame to prevent damage to the bushing. Any worries about heating the frame too much?
Forum: Suspension 07-02-2013, 06:27 AM
Replies: 26
Views: 17,584
Posted By gringoti
This an amazing thread. I need to do all this to...

This an amazing thread. I need to do all this to the right sway bar support/mount which has rusted and cracked. What bolts are used to hold the clamp to the support. Size and grade please? These are...
Forum: US and North America 12-15-2010, 06:25 AM
Replies: 32
Views: 80,987
Posted By gringoti
Hatch parcel deck

The parcel deck/hatchcover or whatever the heck the interior cover for the trunk area is called has two straps that hook to the hatch exterior rear door that pull the deck up and open when you open...
Forum: US and North America 12-15-2010, 05:35 AM
Replies: 32
Views: 80,987
Posted By gringoti
Glovebox door if latch handle is good??

Hi,
I would buy your glove box door if the handle is not broken. Also rear hinging deck and hinge parts for it that are on car.
Greg
Forum: Exhausts 08-28-2010, 05:34 AM
Replies: 5
Views: 1,471
Posted By gringoti
Thanks.

I used universal muffler brackets and muffler clamps at either end of the Magnaflow 11134 muffler. I attached the front universal bracket to the stock rubber ring with a 3" bolt. It is kind of long...
Forum: Exhausts 08-20-2010, 04:02 AM
Replies: 5
Views: 1,471
Posted By gringoti
Those pins on the muffler...

Those pins on the muffler that insert into the rubber muffler hanger .... What do you do to install a generic muffler without them? I just ordered a Magnaflow that is a bit smaller and has no pins.
...
Showing results 1 to 12 of 12

 
Forum Jump

All times are GMT +1. The time now is 05:10 AM.

Donate - Contact Us - www.318ti.org - Archive - Top

.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
[page compression: 49.31 k/56.24 k (12.32%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.