318ti.org forum - View Single Post

jjannull · 12-12-2012, 07:00 AM

Thought I would jump in here - I found a bunch of fob programming instructions:

To program the key fob for the early model BMW 3 series including the 318 you have to
start with all doors, trunk and hood closed.
(these aren't mine, they were all found here http://programcarremotes.com/bmw/bmw...e-programming/ - I think they have other model years as well)

There are several different methods to try for the BMW 3Series so you may have to try more
than one. TIP – if one method fails the first time, try it a second time before moving on
to a new method as they can be tricky to get the steps right

METHOD ONE
Step one – Open the Trunk

Step two – get in the drivers side of the vehicle and close the door

Step three – insert the key into the ignition and turn it ‘ON’ and ‘OFF’ five times ending in the ‘OFF’ position.

Your car should indicate that it is ready for programming by emitting a loud ‘chirp’ noise.

Step four – open and close the drivers door (but stay in the seat)

Step five – press any button on the key fob.

The light should flash indicating that programming has been succesful

Step six – repeat steps three and four again for other remotes your wish to program.

Step seven – when you have finished programming key fobs, leave the door open, get out and close the trunk and then close the drivers door.

Your car should indicate that it has completed programming mode by emitting another loud ‘chirp’ noise.

METHOD TWO

Step one – get in the drivers side of the vehicle and close the door

Step two – insert the key into the ignition and turn it ‘ON’ and ‘OFF’ five times ending in the ‘OFF’ position.

Step three – remove the key from the ignition and hold down the UNLOCK button for 15 seconds while pressing the LOCK button three times rapidly.

Step four – release both buttons

Your car should indicate that the key fob has been programmed by cycling the door locks.

METHOD THREE

this method requires at least one working key fob. If it doesn’t work the first time switch the order of the keys.

Step one – get in the drivers side of the vehicle and close the door

Step two – insert the key into the ignition and turn it quickly from ‘ON’ to ‘OFF’. All the rest of the steps MUST occur in 30 seconds or less.

Step three – remove key #1 and hold it up near the roof on the drivers side by your shoulder (this is where the reciever is located)

Step four – hold down the UNLOCK button for 15 seconds while pressing the LOCK button three times rapidly.

Step five – release the unlock button

Your car should indicate that the key fob has been programmed by cycling the door locks.

Step six – repeat step three, four, five fast for key #2.

12-12-2012, 07:00 AM	#57
jjannull Junior Member Join Date: Dec 2012 Location: canada Posts: 1 iTrader: (0) Photo Gallery	programming instructions for BMW 3Series most years Thought I would jump in here - I found a bunch of fob programming instructions: To program the key fob for the early model BMW 3 series including the 318 you have to start with all doors, trunk and hood closed. (these aren't mine, they were all found here http://programcarremotes.com/bmw/bmw...e-programming/ - I think they have other model years as well) There are several different methods to try for the BMW 3Series so you may have to try more than one. TIP – if one method fails the first time, try it a second time before moving on to a new method as they can be tricky to get the steps right METHOD ONE Step one – Open the Trunk Step two – get in the drivers side of the vehicle and close the door Step three – insert the key into the ignition and turn it ‘ON’ and ‘OFF’ five times ending in the ‘OFF’ position. Your car should indicate that it is ready for programming by emitting a loud ‘chirp’ noise. Step four – open and close the drivers door (but stay in the seat) Step five – press any button on the key fob. The light should flash indicating that programming has been succesful Step six – repeat steps three and four again for other remotes your wish to program. Step seven – when you have finished programming key fobs, leave the door open, get out and close the trunk and then close the drivers door. Your car should indicate that it has completed programming mode by emitting another loud ‘chirp’ noise. METHOD TWO Step one – get in the drivers side of the vehicle and close the door Step two – insert the key into the ignition and turn it ‘ON’ and ‘OFF’ five times ending in the ‘OFF’ position. Step three – remove the key from the ignition and hold down the UNLOCK button for 15 seconds while pressing the LOCK button three times rapidly. Step four – release both buttons Your car should indicate that the key fob has been programmed by cycling the door locks. METHOD THREE this method requires at least one working key fob. If it doesn’t work the first time switch the order of the keys. Step one – get in the drivers side of the vehicle and close the door Step two – insert the key into the ignition and turn it quickly from ‘ON’ to ‘OFF’. All the rest of the steps MUST occur in 30 seconds or less. Step three – remove key #1 and hold it up near the roof on the drivers side by your shoulder (this is where the reciever is located) Step four – hold down the UNLOCK button for 15 seconds while pressing the LOCK button three times rapidly. Step five – release the unlock button Your car should indicate that the key fob has been programmed by cycling the door locks. Step six – repeat step three, four, five fast for key #2.