318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Engine


Engine Tuneups, chips, wires, spark plugs.

» Recent Threads
First BMW
05-13-2022 06:24 PM
Last post by J!m
Today 11:49 AM
2 Replies, 389 Views
Danny's 318ti Thread...
05-03-2022 07:13 PM
Last post by J!m
Today 11:45 AM
6 Replies, 549 Views
Biolite's Build
05-11-2022 02:28 AM
Last post by J!m
05-16-2022 11:48 AM
4 Replies, 1,117 Views
1995 BMW 318ti for sale
04-29-2022 05:46 PM
Last post by baby_bimmer
05-14-2022 09:06 PM
6 Replies, 1,825 Views
Reply Share/Bookmark
Thread Tools Display Modes
Old 04-05-2020, 06:17 PM   #1
Junior Member
Join Date: Apr 2020
Location: VA
Posts: 5
iTrader: (0)
Default Engine Won't Start - No Power to Fuel Pump Fuse

I am helping my neighbor troubleshoot his 95 318ti with a standard transmission. He replaced the motor. The car did start and run with the new engine. After a few minutes he turned it off, took it off of the jack stands, restarted it, and drove it just outside of the garage where he left it idling. I am not sure how long he left it idling, but he said after a little bit it started to spit, sputter, and backfire then shut off. It would not restart. He is not an electrical guy so he has been throwing parts at it.

Reading this thread it was like he was having the same exact issue. Unfortunately, there was no solution posted.

There is no power to fuse 18. All grounds are good. The DME, fuel pump, and oxygen sensor relays have all been replaced.
The DME relay energizes correctly, but the fuel pump relay and subsequently the oxygen sensor relay do not (pin 30 of the oxygen sensor relay is fed from pin 87 of the fuel pump relay). I have traced the wires going from the relays to the DME and they all have good continuity so there is no break in a wire.

The cam and crank position sensors are new, fuel pump is new, temp sensor is new. I can jump the fuel pump relay and you can hear it working.

Pin 85 on the fuel pump relay that goes to pin 1 on the DME always has power to it. Unlike pin 85 on the DME relay. That shows power, but when they key is turned to ACC the voltage drops to .8 VDC and the relay is energized. I suspect that the DME is not removing the power to pin 85 of the fuel pump relay like it should to energize the relay. But why isn't it doing that? What other input to the DME is causing it not to remove the power to energize the relay?

I may have forgotten some things we tested and readings I took, but if anyone has any questions or suggestions we are all ears. What boggles me is that the car ran and ran strong for what little time it was running.
Harsh is offline   Reply With Quote
Old 04-07-2020, 10:11 PM   #2
Junior Member
Join Date: Apr 2020
Location: VA
Posts: 5
iTrader: (0)

A little update.

I have had a bit of I am an idiot moment. I do get power through the fuel pump relay and to the fuel pump fuse. When I was previously testing it I was doing with the ignition in ACC. When I try to start the car the relay energizes and provides power to the fuse. However, the car just cranks and cranks. If I just keep cranking it every once in a blue moon it will give me a little sign that it wants to kick over. When it does that the RPM gauge jumps up to about 3-4K and the mpg gauge jumps as well. Other than when the engine gives that tiny sign that it wants to kick over the gauges do not move.

I also tried to see if there were any codes stored in the DMC. I never get the initial sequence of initial sequence of flashes. The light will stay illuminated for 2.5 seconds, give a quick flash, stay illuminated for 2.5 seconds, give a quick flash. It will just continue to repeat that pattern until I turn the ignition off. The owner of the car even tried a scanner and he said he couldn't pull any codes.

Last edited by Harsh; 04-07-2020 at 10:46 PM.
Harsh is offline   Reply With Quote
Old 05-04-2020, 12:09 AM   #3
Junior Member
Join Date: Apr 2020
Location: VA
Posts: 5
iTrader: (0)

After testing just about everything in the car a friend of he owner was able to get a hold of a DME.

As soon as we plugged it in, cranked the car, it came to life and ran smooth as butter.

He said the DME we had was for a 6 cylinder. I question that. The VIN that is on the computer matches the cars VIN. Decoding the VIN it shows to be a 4 cylinder car so I don't understand how it could have changed. Regardless, the car runs so it really doesn't matter to me.

Pic of the DME that works.
Harsh is offline   Reply With Quote


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Fuel Leaking from or near Tank area - crank no start Rudenice Exterior 10 03-05-2017 11:44 PM
S54 engine into late model E36 swap (same 318ti) Hakentt-MS41.1 Engine Swaps 11 11-03-2015 04:08 PM
328ti Post Swap Analysis BMW_Hatchback Engine Swaps 6 06-29-2011 06:12 AM
Fuel pump HELP!! sim-simma Electrical 2 04-24-2011 06:05 PM
error code list biorjin Exhausts 0 10-10-2005 01:55 AM

All times are GMT +1. The time now is 10:14 PM.

Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2022, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 67.47 k/77.91 k (13.40%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.