318ti.org forum

Go Back   318ti.org forum > Garage > General Chit Chat

Notices

General Chit Chat Anything other than automotive related.

.
» Recent Threads
Rudolph the Red 318ti
05-06-2019 10:49 PM
Last post by MisterM52
Today 10:45 AM
20 Replies, 2,853 Views
Hi All
06-23-2019 03:50 PM
Last post by MisterM52
Today 10:40 AM
5 Replies, 340 Views
Ultimate Supercharger...
06-23-2019 08:06 AM
Last post by MisterM52
Today 03:21 AM
6 Replies, 452 Views
BMW Individual Interior...
05-14-2019 04:38 PM
Last post by runnr548
Yesterday 11:45 PM
3 Replies, 831 Views
Odd starting issue after...
06-10-2019 03:48 PM
Last post by paul somlo
Yesterday 08:43 PM
8 Replies, 691 Views
Swap Manual Q&A
01-09-2007 03:32 AM
Last post by J!m
Yesterday 06:48 PM
206 Replies, 64,323 Views
As Green as the Touge - ...
06-18-2016 02:47 PM
Last post by anassa
Yesterday 05:04 PM
45 Replies, 23,898 Views
How much is too much $...
06-22-2019 10:31 PM
Last post by anassa
Yesterday 04:03 PM
2 Replies, 354 Views
E8x Rear Subframe Rust
06-23-2019 04:31 PM
Last post by OllieNZ
06-23-2019 04:31 PM
0 Replies, 214 Views
Long lost 1996 318ti
06-19-2019 08:46 PM
Last post by BRADESTAR
06-22-2019 05:29 AM
3 Replies, 561 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 05-23-2019, 07:09 PM   #196
andakn
Member
 
Join Date: Nov 2015
Location: missouri
Posts: 78
iTrader: (0)
Default

2nd downpipe, just need to do the O2 bongs and figure out how I want the Wastegate to be. Hopefully I will start to install it this weekend.
Attached Thumbnails
Click image for larger version Name:	20190522_194350.jpg Views:	18 Size:	73.3 KB ID:	17644   Click image for larger version Name:	20190522_194237.jpg Views:	18 Size:	82.6 KB ID:	17645  
andakn is offline   Reply With Quote
Old 05-27-2019, 03:00 PM   #197
andakn
Member
 
Join Date: Nov 2015
Location: missouri
Posts: 78
iTrader: (0)
Default

Getting close, I have to relocate the expansion tank and get some oil line fittings
Attached Thumbnails
Click image for larger version Name:	20190526_200015.jpg Views:	18 Size:	96.5 KB ID:	17654   Click image for larger version Name:	20190526_195932.jpg Views:	19 Size:	99.4 KB ID:	17655  
andakn is offline   Reply With Quote
Old 05-28-2019, 03:49 AM   #198
andakn
Member
 
Join Date: Nov 2015
Location: missouri
Posts: 78
iTrader: (0)
Default

Well I did run it for a few minutes, but still have some things to finish up. I need the correct oil feed fitting with restrictor, a second egt sensor bung and finish the rest of the "legal" downpipe/exhaust. I really need to invest in a tig welder and try and switch mainly because I'd like to learn to weld aluminum.
andakn is offline   Reply With Quote
Old 06-03-2019, 11:51 PM   #199
andakn
Member
 
Join Date: Nov 2015
Location: missouri
Posts: 78
iTrader: (0)
Default

To scoop, or not to scoop, that is the question. Looking for input. It would make the turbo function better but not sure if I like it. Just mocking it up before I commit to cutting the hood.
Attached Thumbnails
Click image for larger version Name:	20190603_174447.jpg Views:	10 Size:	84.5 KB ID:	17680   Click image for larger version Name:	20190603_174417.jpg Views:	10 Size:	92.6 KB ID:	17681  
andakn is offline   Reply With Quote
Old 06-13-2019, 05:42 PM   #200
andakn
Member
 
Join Date: Nov 2015
Location: missouri
Posts: 78
iTrader: (0)
Default

Well the car was running very well, and no more boost creep with the bigger turbo. So I started turning the boost back up. At 30 psi it was screaming and after a few pulls I noticed that when the engine went back under vaccum it would burn oil and clear out under boost. Since I am running a catch can that vents not to the intake the only thing that would do this is the valve guide seal. If I remember correctly the valve spring does not hold down the valve guide seal like most engines I think I might of lifted a seal under the 30psi of boost. Just starting to tear it apart to verify.
andakn is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Pics of New Engine with DASC Mendi3 Lounge 37 10-14-2005 07:37 PM
new engine and dasc (pictures) marcus2116 Lounge 10 08-08-2005 09:07 PM
Engine and DASC supercharger installed on it $3000 Silver00spike US and North America 13 07-17-2005 11:07 PM
Engine Swap vs. Turbo or Both? Virgil Induction 1 05-23-2005 07:17 PM
Engine Swap vs. Turbo or Both? Virgil Engine Swaps 8 04-30-2005 08:12 AM


All times are GMT +1. The time now is 11:33 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2019, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 84.90 k/99.01 k (14.25%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.