» Site Navigation | | » Recent Threads | | | | | | | | 01-08-2019, 09:20 PM | #1 | Member Join Date: Mar 2010 Location: CALIFORNIA Posts: 82 | about block coolant pipe hey just wondering if anyone knows another way to change the coolant pipe that is on the block mine started leaking real bad and have low funds so cant take it to the mech im doing it myself so far i took of the upper intake manifold to take of the bottom one seems like to much work but if that is the only way i will do it thanks ! | | | 01-10-2019, 12:40 AM | #2 | Senior Member Join Date: Sep 2006 Location: Greeley CO Posts: 233 | I doubt that it can be done without removing the lower intake - and I've spent a fair amount of time staring at that coolant pipe and running through it in my mind. I just don't know how you would get at the hoses towards the firewall. Dealing with the lower intake is no picnic, but it's not a showstopper - I'm sure you can deal with it. Most people run into problems with the starter connections - the way the lugs are sized, it's somewhat self explanatory as to where they go. And you could label the rest of the connectors with masking tape, although the last time I did this, I remember them going back together with little ambiguity, either due to pin count or harness length. Try it - see if it can be done with the lower intake in place. If so, report back, and you'll be a hero. If not, then proceed with removing the intake. By the way, there's a writeup in the Knowledge Base here concerning cooling system overhaul. There should be some pics of the lower intake manifold being removed and reinstalled. Last edited by paul somlo; 01-10-2019 at 12:43 AM. | | | 01-10-2019, 01:35 AM | #3 | Junior Member Join Date: Apr 2018 Location: Austin, TX Posts: 28 | You're nearly halfway there already. Just go for it! Once you color code all the wires (I bought a pack of electrical tape, assorted colors for ~$6 at Lowe's) and unbolt the starter wires (which I also labelled), the LIM isn't that bad. | | | 01-10-2019, 07:41 PM | #4 | Member Join Date: Mar 2010 Location: CALIFORNIA Posts: 82 | Quote: Originally Posted by paul somlo I doubt that it can be done without removing the lower intake - and I've spent a fair amount of time staring at that coolant pipe and running through it in my mind. I just don't know how you would get at the hoses towards the firewall. Dealing with the lower intake is no picnic, but it's not a showstopper - I'm sure you can deal with it. Most people run into problems with the starter connections - the way the lugs are sized, it's somewhat self explanatory as to where they go. And you could label the rest of the connectors with masking tape, although the last time I did this, I remember them going back together with little ambiguity, either due to pin count or harness length. Try it - see if it can be done with the lower intake in place. If so, report back, and you'll be a hero. If not, then proceed with removing the intake. By the way, there's a writeup in the Knowledge Base here concerning cooling system overhaul. There should be some pics of the lower intake manifold being removed and reinstalled. | Hey thanks for the info I really appreciate this awesome community ! I cant believe I was able to remove and install the part leaving the lower manifold on! i did have to disconnect the fuel lines and fuel rail and loosen the "squid" but thats it and was also able to change all 3 hoses that connect to the pipe.. I heard of people taking of the oil housing for more room but I didnt want to do that..my hands are also big someone with smaller hands can probably do it faster.. it was not easy and most was done by feeling around but it can be done! I need to do a write up for everyone here with pictures and tools I used I drove around for a while seems alright but taking out today to test it some more thanks again! Last edited by 2MIZ129; 01-10-2019 at 07:44 PM. | | | 01-10-2019, 07:43 PM | #5 | Member Join Date: Mar 2010 Location: CALIFORNIA Posts: 82 | Quote: Originally Posted by Locus7 You're nearly halfway there already. Just go for it! Once you color code all the wires (I bought a pack of electrical tape, assorted colors for ~$6 at Lowe's) and unbolt the starter wires (which I also labelled), the LIM isn't that bad. | Hey thanks for that I did go buy some just incase my idea of leaving on the lower manifold didnt work but i guess it did work hopefully its a solid instal and it wont leak later on lol ill post a write up on it soon thanks so much! | | | 01-11-2019, 10:26 PM | #6 | Junior Member Join Date: Nov 2018 Location: California Posts: 1 | I just finessed it in there, connect the back hose first, then shove it in make sure it’s actually in the block or it will still leak I used black silicone to seal mine, but you have to take the top half of the intake off and then just connect the top tube after it’s in, it takes a little effort but it’s easy. Sent from my iPhone using Tapatalk | | | | Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | | Posting Rules | You may not post new threads You may not post replies You may not post attachments You may not edit your posts HTML code is Off | | | |