318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Electrical

Notices

Electrical All wiring questions.

.
» Recent Threads
1999 M-Sport For Sale
12-31-2023 05:10 PM
Last post by Coop540iT
03-23-2024 06:39 PM
1 Replies, 99,239 Views
Once again 318ti owner...
03-20-2024 12:39 PM
Last post by two30grain
03-22-2024 02:04 PM
1 Replies, 62,197 Views
What brakes do I...
03-20-2024 03:27 PM
Last post by huirtera
03-20-2024 03:27 PM
0 Replies, 59,464 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 04-05-2004, 02:13 AM   #1
clex2
Senior Member
 
clex2's Avatar
 
Join Date: Nov 2003
Location: Walnut Creek, CA
Posts: 642
iTrader: (1)
Default

After buying a M3 gauge cluster for my 330ti, I found that the MPG gauge did not work. (Flame if you want about how useless this gauge is, I'm happy cuz I was able to make it work) It turns out that 318ti, as equipped from the factory, are not wired for MPG guages. For all those who have 6 cylinder conversions and gauge transplants with erratic, non-functioning MPG gauges, read on (318ti's, 318i's etc.)

Parts needed:
circular connector 61-13-0-007-570 (fits in X20)
bushing contact 61-13-0-005-201 (fits in X16)
approx 3.5 feet of 18 guage wire, solder, shrink tubing, wire ties,...

Using Bentley, I figured that the white/black wire coming out of the DME is the signal for fuel consuption. It runs accross the back engine bay to the X20 connector which is a big black round connector next to the fuse box. You twist to unlock and open it. You will find that the female side (top part connected to DME) has a connection for pin #24, but the male side has the hole for pin #24 empty. (You can make sure that this is indeed the white/black wire by pulling back the protective rubber boot on the female connector). You need to put the male circular connector in this slot. However, it is not as simple as just sliding it in. If you look carefully, there is a thin locking ring between the inner and outer rows if pins. This needs to be turned one click counter clockwise. Use flat jewlers screwdrivers to pry the locking tabs away while turning. It turns freely once the tabs are cleared. Now you can push the circular connector all the way in. Be sure to return the locking ring to it's original locked position.

From the newly placed male pin connector, run a length of 18 gauge wire (about 3.5 feet) onto the fuse box (open it by undoing the 4 torx screws) and through the common fire wall wire opening into the driver footwell. Thread it along with the wire bundles that go the X16 connector on the tach side of the instrument cluster.

Remove the instrument cluster and remove the x16 connector from the back of the cluster. there is a pivoting lever that swings up to release the connector. Open the X16 connector by prying off the sliding cover. A double row of female pin connectors slides out. Pin #21 is empty and needs the bushing contact to be inserted. Connect the two wire ends together to complete the connection. Tidy up the wiring, put the cluter back and there you have it.
clex2 is offline   Reply With Quote
Old 06-25-2012, 09:25 PM   #2
eurohb
Senior Member
 
eurohb's Avatar
 
Join Date: May 2009
Location: Orange County, CA
Posts: 2,019
Vehicles
iTrader: (2)
Default

no way we can get this to work on a 4cylinder :/
__________________
V2 in progress.
Volkswagen MK6 GTI
eurohb is offline   Reply With Quote
Old 07-16-2012, 04:06 AM   #3
KSKarl
Senior Member
 
Join Date: May 2010
Location: Wichita, KS
Posts: 111
iTrader: (0)
Default

On my car, '95, that black/white wire fed the dashboard computer display so it can figure out mpg. I just jumpered from the computer to the gage connector. The wire was the right size for the gage connector plug to grip as is, so the pin on the gage cluster just sticks straight into the wire.

Did the same when I rigged fog lights so the fog light indicator in the gage cluster works.
KSKarl is offline   Reply With Quote
Old 07-26-2017, 02:38 AM   #4
mnguyen84
Junior Member
 
Join Date: Apr 2017
Location: United States
Posts: 28
iTrader: (0)
Default

The odometer on my 96 318ti also has an mpg gauge that does not work.. Is this part from another car and not stock?
mnguyen84 is offline   Reply With Quote
Old 07-26-2017, 01:20 PM   #5
KSKarl
Senior Member
 
Join Date: May 2010
Location: Wichita, KS
Posts: 111
iTrader: (0)
Default

Quote:
Originally Posted by KSKarl View Post
On my car, '95, that black/white wire fed the dashboard computer display so it can figure out mpg. I just jumpered from the computer to the gage connector. The wire was the right size for the gage connector plug to grip as is, so the pin on the gage cluster just sticks straight into the wire.

Did the same when I rigged fog lights so the fog light indicator in the gage cluster works.
I should explain that my car was a conversion, the engine and gage cluster were from an M3. But the computer was original for the 4cyl. But I don't see why the same approach would not work with a 4cyl car, if a gage cluster with the MPG display has been swapped in. Just jumper the MPG lead from the dash computer to the contact on the gage cluster as described in the detailed instructions above.
KSKarl is offline   Reply With Quote
Old 07-26-2017, 08:39 PM   #6
mnguyen84
Junior Member
 
Join Date: Apr 2017
Location: United States
Posts: 28
iTrader: (0)
Default

my 1.9L z3 had a digital display of mpg. but my 318ti doesn't....it only has a digital clock with 2 buttons to change the hour and minutes.

can i still jump the mpg from the dash to the gauge?
mnguyen84 is offline   Reply With Quote
Old 07-27-2017, 01:09 AM   #7
KSKarl
Senior Member
 
Join Date: May 2010
Location: Wichita, KS
Posts: 111
iTrader: (0)
Default

I think you need to run a wire from the DME connector like clex said above.
KSKarl is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 09:33 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 77.49 k/91.68 k (15.47%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.