318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Exterior

Notices

Exterior From spoilers, lights to body kits and window problems.

.
» Recent Threads
Brakelights not working
05-17-2019 07:59 PM
Last post by PNWm52Project
Yesterday 04:41 PM
4 Replies, 318 Views
new engine build. dasc +...
01-02-2016 01:28 AM
Last post by andakn
Yesterday 03:49 PM
193 Replies, 97,758 Views
DIY X-Brace & Support...
Yesterday 11:12 AM
Last post by MisterM52
Yesterday 11:12 AM
0 Replies, 89 Views
Rudolph the Red 318ti
05-06-2019 10:49 PM
Last post by MisterM52
Yesterday 10:54 AM
11 Replies, 1,060 Views
M44 strange water leak...
05-18-2019 09:01 AM
Last post by MisterM52
Yesterday 09:53 AM
4 Replies, 284 Views
Valve cover gaskets?
05-13-2019 10:05 PM
Last post by MisterM52
05-18-2019 10:16 PM
4 Replies, 474 Views
For sale - parts off 96...
05-08-2019 12:30 AM
Last post by bazar01
05-18-2019 04:06 PM
1 Replies, 428 Views
M-tech bumper - avus...
05-05-2019 02:41 PM
Last post by cmoore
05-18-2019 02:20 AM
8 Replies, 1,121 Views
Jean's Turbo Build -...
08-18-2009 03:08 AM
Last post by andakn
05-18-2019 12:45 AM
534 Replies, 145,063 Views
DASC considering part out
05-04-2019 11:42 PM
Last post by PNWm52Project
05-18-2019 12:11 AM
5 Replies, 747 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 09-20-2018, 09:05 AM   #1
paul somlo
Senior Member
 
Join Date: Sep 2006
Location: Greeley CO
Posts: 196
iTrader: (0)
Default Manual Adjustment of Headlight Level Motors?

I just installed a pair of euro projectors, with leveling motors. How can the leveling motors be adjusted manually, without wiring? And how do they interact with the two adjustments on the back of each headlight?
paul somlo is offline   Reply With Quote
Old 09-20-2018, 12:08 PM   #2
John Firestone
Senior Member
 
John Firestone's Avatar
 
Join Date: Nov 2004
Location: Bremerhaven, Germany
Posts: 970
iTrader: (0)
Default

A headlight motor, item 12, has a long rod ending in a ball that snaps into the bottom of the headlight reflector. The rod and ball extend and retract, to tilt the reflector up and down.

The motor is set up as a servo that tracks the setting of the dash, headlight range adjustment potentiometer. The motors are likely where the pot last sat when it and the motors last saw power. Most likely that was at the zero, the car normally loaded position, with no downward headlight trim. That is where mine have sat for ages.

If you want, you can remove the motors and substitute two of item 11: to fix the headlights at the zero, untrimmed position. I wish I could do that on the right side, as the motor can get in the way when I work on the car.

Last edited by John Firestone; 09-22-2018 at 08:37 AM. Reason: down <-> up
John Firestone is offline   Reply With Quote
Old 09-23-2018, 04:08 AM   #3
paul somlo
Senior Member
 
Join Date: Sep 2006
Location: Greeley CO
Posts: 196
iTrader: (0)
Default

Thank you John - two questions:

What's the "zero" position? The rod all the way out, all the way in, or some intermediate position?

How does item "11" work? Is it fixed, or manually adjustable.

I took my lights apart today, and it's apparent that the level motor is necessary, as it acts as the lower pivot point for the entire reflector assembly.
paul somlo is offline   Reply With Quote
Old 09-23-2018, 08:42 AM   #4
John Firestone
Senior Member
 
John Firestone's Avatar
 
Join Date: Nov 2004
Location: Bremerhaven, Germany
Posts: 970
iTrader: (0)
Default

The range control and motors lets you tilt the headlights downward when the front of the car is tilted slightly upward after loading the rear of the car with passengers, cargo or a trailer.

0 is the normal position: the rod fully extended to give no downward headlight tilt. Item 11, a stiff piece of plastic is made to that length, to hold the reflector at position 0.
John Firestone is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
318ti use Z3 DME for SAP delete and emissions delete new318tifan Engine 5 02-03-2016 03:24 PM
Sold the wrong oil pan HELP! fast2002 Maintenance 4 01-27-2012 04:16 AM
Remote headlight adjustment eshtebah Exterior 5 10-12-2009 12:12 AM
Headlight Adjustment DGWGuitars Exterior 1 10-27-2005 08:15 AM
Stock Headlight Adjustment Tyler Exterior 1 10-08-2005 06:29 AM


All times are GMT +1. The time now is 12:11 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2019, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 75.83 k/88.21 k (14.04%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.