318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Maintenance

Notices

Maintenance Service Interval questions, oil change info.

.
» Recent Threads
1999 M-Sport For Sale
12-31-2023 05:10 PM
Last post by Coop540iT
03-23-2024 06:39 PM
1 Replies, 95,680 Views
Once again 318ti owner...
03-20-2024 12:39 PM
Last post by two30grain
03-22-2024 02:04 PM
1 Replies, 58,618 Views
What brakes do I...
03-20-2024 03:27 PM
Last post by huirtera
03-20-2024 03:27 PM
0 Replies, 56,040 Views
M50+manual swap bastard...
03-01-2024 11:00 PM
Last post by Andy318
03-18-2024 02:34 PM
3 Replies, 130,941 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 11-17-2018, 04:56 AM   #1
S.W.B.C
Junior Member
 
Join Date: Dec 2009
Location: Oregon
Posts: 17
iTrader: (0)
Default SIR crankshaft tool

Grasping at straws but anyone in the Portland area that has the SIR tool for securing harmonic balancer for removing the crankshaft bolt? Rent , barter, or trade for beer or???
Thanks so much!!!!!
Silas
S.W.B.C is offline   Reply With Quote
Old 11-24-2018, 04:20 AM   #2
paul somlo
Senior Member
 
Join Date: Sep 2006
Location: Greeley CO
Posts: 233
iTrader: (0)
Default

I use a pin to lock the flywheel - the tip is 0.307 diameter and 0.392 in length, the next section is 0.452 in diameter and 1.577 inches in length. The next larger section doesn't matter.

You might get away using a 5/16" drill bit or an 8mm bolt.

I was concerned that I'd be stressing the crankshaft, but I've used it several times now with no ill effects, and I've read accounts of others doing likewise.
Attached Thumbnails
Click image for larger version Name:	PB232533.JPG Views:	78 Size:	84.9 KB ID:	17417  
paul somlo is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
crankshaft pulley holding tool rbush Engine 16 02-28-2016 09:36 PM
Misc parts FS: M44 Crank Locking Pin/Dowel Tool for Head repair 96silver318ti Parting out & Parts (US) 4 08-22-2013 10:58 PM
DIY: R&R crankshaft position sensor elfhearse Knowledge Base 4 05-12-2010 03:24 AM
MemoScan B200 SRS/Airbag Tool CirrusSR22 Maintenance 6 05-30-2009 07:21 PM
Source for rear subframe bushing tool. bullmand Suspension 7 12-13-2007 05:07 PM


All times are GMT +1. The time now is 10:32 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 61.68 k/71.18 k (13.34%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.