318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Knowledge Base


Knowledge Base How to articles and things explained.

» Recent Threads
97 318Ti 5-Speed NJ
Today 03:12 AM
Last post by manydubs
Today 02:09 PM
1 Comments, 166 Views
Suspension Upgrade FAQ -...
03-14-2007 03:06 AM
Last post by Sylvia
Today 10:27 AM
70 Comments, 60,337 Views
M-Sport steering wheels
02-06-2018 06:57 PM
Last post by Mr.Squeelerz
Yesterday 04:20 PM
9 Comments, 1,415 Views
Are the 60-2 impulse...
03-16-2018 05:43 AM
Last post by apexspeedtech
Yesterday 03:29 PM
2 Comments, 454 Views
Oem M3 mirrors for 318tis
02-28-2018 02:20 AM
Last post by Dustoff44
Yesterday 02:47 PM
10 Comments, 883 Views
Improve the oversteer...
03-08-2018 04:39 PM
Last post by manydubs
Yesterday 12:43 PM
5 Comments, 435 Views
Has anybody modified ASC...
03-07-2018 12:24 PM
Last post by sirius815
Yesterday 11:51 AM
12 Comments, 937 Views
AEM M42 woes
03-17-2018 04:53 AM
Last post by Whizbang
03-17-2018 04:53 AM
0 Comments, 175 Views
Euro glass headlights
09-24-2014 10:27 PM
Last post by angelicmisskitty
03-16-2018 11:17 PM
189 Comments, 103,177 Views
Swap Manual Q&A
01-09-2007 03:32 AM
Last post by ambitious1
03-16-2018 05:32 AM
187 Comments, 43,261 Views
Comment Share/Bookmark
Tutorial Tools Display Modes
How to program a new key fob
How to program a new key fob
1996 bmw 318ti
Published by anthonyl
Default How to program a new key fob

If your short a key fob or lost yours this is a cheap way to replace it. I purchased my fob on ebay for $30 and programmed it myself.

**Read all the way through. The last line is important.**

1. Make sure all doors, hood and trunk are closed.

2. Open the trunk door.

3. Open the drivers door and sit in the drivers seat.

4. Close the drivers door.

5. Turn ignition switch to on and off 5 times ending in off.(do not start the car turn to just before starting)
Your alarm light will turn on and the siren on the alarm will chirp to let you know it is ready.
(this can also be used to test if you have the alarm)

6. Open the drivers door stay in the seat close the drivers door.

7. Press any button on the remote. The light will flash to indicate your remote has been programmed.

8. Repeat steps 6 & 7 to program any other remotes, up to 4 remotes a car.

9. To exit program mode open drivers door leave the door open. Close the trunk lid and close the drivers door the
siren should chirp again and the red light will shut off. Test your remotes to make sure they work right.

******Note all the steps from 2 - 5 must be done within 45 seconds. Step 5 must be done within 10 seconds.

And there ya have it, as simple as that.

Information was taken from: http://programyourremote.com/
Tutorial Tools

By spidertri on 09-08-2008, 03:33 PM

I'm pretty sure this procedure only works for the later model 2 button remote. Not sure about the earlier 3 button one.

But yeah, I also bought a remote off of ebay for like $30, procedure worked like a charm.
Reply With Quote
By Bozola on 01-24-2009, 05:37 PM

It worked!
marijuana dispensaries
Last edited by Bozola; 01-31-2011 at 02:11 PM..
Reply With Quote
By b-rad on 02-02-2009, 07:34 AM

Originally Posted by Bozola View Post
It worked!
Do you have the 2 or 3 button remote? I need to do this, but i require the 3 button remote..
Reply With Quote
By wolferj-RIP on 02-02-2009, 08:31 PM

Originally Posted by b-rad View Post
Do you have the 2 or 3 button remote? I need to do this, but i require the 3 button remote..
This is the procedure for the later model setup (96+ w/ 2 button remote). I have ordered a replacement 3 button remote and will attempt to program it with these instructions;

"BMW factory keyless alarm unit installed on cars up through August 1995. This controller works with the three-button remote. The alarm controller is programmed to work with a specific remote by synchronizing the small chip in the remote to the alarm unit. Open up the alarm remote, and carefully remove the small chip (red arrow, lower right inset). Then pull out the alarm unit from your car, leaving the main wire harness attached. Insert the chip from the remote into the connector in the unit (blue arrow). Then turn on the ignition, and press the reset button for at least 10 seconds (green arrow). The red alarm indicator on your center console should flash, indicating that the codes have been read and accepted. Turn off the ignition, reinstall the chip in your remote, and test itóit should work! "

quoted from here;


I will post up on my experience when I attempt it...
Reply With Quote
By wolferj-RIP on 02-02-2009, 09:48 PM
Default 3 button remote programming

The above instructions worked perfectly! If you have any question (like I did) regarding whether your factory alarm is the earlier unit or the later unit, here are the #'s for the earlier 3 button alarm system which was installed in e36's with production dates of 8/95 and earlier;

(as Dave noted below, there are always exceptions to the rules. Such as an earlier style alarm installed in a later production car. My car was not shipped with the alarm system, but was most likely added by the dealer as an upsell or by the request of the purchaser, as it is OEM. So your results may vary)

the FCC ID# for the 3 button system Alarm Brain is #A269ZUA070 and the remote FCC ID# is A269ZUA071.

PM me if you have any auestions!

Good luck...
Reply With Quote
By pdxmotorhead on 02-03-2009, 07:42 AM

My 10/95 has the early style with the chip inside, the alarm box has a matching chip.

Reply With Quote
By HuGo on 04-01-2009, 09:28 AM

I just tried doing this and it didn't work. My car is a 5/96 and I bought a 2 button remote. I didn't hear any chirp or the remote light up or anything
Reply With Quote
By performanceisland on 04-01-2009, 01:31 PM

Originally Posted by HuGo View Post
I just tried doing this and it didn't work. My car is a 5/96 and I bought a 2 button remote. I didn't hear any chirp or the remote light up or anything
is it a 2 button remote? if so replace the battery, the remote light shoudl light when any of the two buttons is pressed unless the battery is dead, the above procedure does work, sometimes it takes a few times to do it, as there are time limits on the steps, and sometimes we simple do the wrong thing, then you have to start over.
Reply With Quote
By HuGo on 04-01-2009, 11:05 PM

I took out the glove box to get to the box (keyless entry). In pelican parts it says to disconnect to disarm the system. Should I leave it disconnected and try the procedure? Or connect back on and do the procedure? I was doing the steps fine from 5x on and off and open close door. I didnt even hear that chirp
Reply With Quote
By wolferj-RIP on 04-01-2009, 11:19 PM

Hugo, I think you should go ahead and disconnect the system, wait a few minutes, reconnect it, then try again... also make sure the alarm fuse is good...
Reply With Quote
By HuGo on 04-02-2009, 12:21 AM

I disconnected it and reconnected it. Fuses are good. Alarm button has battery. Still didnt programmed.
Reply With Quote
By wolferj-RIP on 04-02-2009, 01:02 AM

Damn, that sucks... I cannot think why it isn't working.. Sorry.
Reply With Quote
By HuGo on 04-02-2009, 01:54 AM

Just to throw it out there...does the engine/ecu swap have anything to do with it? And obviously by trunk they mean hatch right?
Reply With Quote
By wolferj-RIP on 04-02-2009, 01:59 AM

Yes, the hatch is the trunk in this case...

As for the ecu swap, I doubt that it could be the issue, but who knows... obviously something is preventing this from working. Maybe try a whole system reboot... disconnect the battery for 15 minutes maybe?

Sorry, I'm out of suggestions...
Reply With Quote


Currently Active Users Viewing This Tutorial: 1 (0 members and 1 guests)
Tutorial Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Tutorial Tutorial Starter Category Comments Last Post
Euro Clear Tails Question JoeyBello Exterior 3 01-16-2008 04:32 AM
Legality of clear indicators ? UK sfj642 Exterior 8 09-05-2007 05:58 PM
Clear light assemblies liquidgraphix US and North America 1 02-20-2007 06:21 PM
318ti Clear Tails & Sidemarkers GregGT US and North America 2 02-12-2007 11:35 PM
Wiring Clear Corners L84THSKY Electrical 17 02-01-2006 09:01 PM

All times are GMT +1. The time now is 03:40 PM.

Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2018, 318ti.org

Tutorial powered by GARS 2.1.8m ©2005-2006
© vBadvanced CMPS v3.2.2
[page compression: 91.76 k/123.02 k (25.41%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.