318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Engine

Notices

Engine Tuneups, chips, wires, spark plugs.

.
» Recent Threads
taillights not working
08-30-2010 08:24 PM
Last post by iski123
Today 01:51 AM
15 Replies, 3,264 Views
Oil Filter Housing Leak...
02-14-2008 09:21 PM
Last post by Locus7
Today 01:06 AM
118 Replies, 80,810 Views
Is this a clubsport?
12-09-2018 06:54 AM
Last post by dranthony
Yesterday 08:44 PM
5 Replies, 259 Views
California Top Trim...
07-16-2014 08:59 AM
Last post by 3DGE
12-09-2018 09:37 PM
9 Replies, 4,499 Views
M42 / M44 loose...
12-07-2018 08:10 PM
Last post by Frach23
12-07-2018 09:34 PM
1 Replies, 338 Views
Anyone seen a carbon...
11-16-2018 06:19 AM
Last post by eurohb
12-07-2018 05:26 AM
1 Replies, 444 Views
New here so lets arc you...
11-09-2018 08:56 AM
Last post by acidjzaz
12-07-2018 12:34 AM
1 Replies, 478 Views
FS: E36 Brakes, rotors,...
12-06-2018 06:30 AM
Last post by FunElan
12-06-2018 09:29 PM
3 Replies, 254 Views
WTB **** 5 Speed BMW...
12-03-2018 02:01 AM
Last post by kaiburger
12-06-2018 08:06 PM
2 Replies, 368 Views
1995 318ti Clusport S52...
10-30-2018 04:31 PM
Last post by Tom318ti
12-06-2018 04:59 PM
5 Replies, 1,130 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 11-05-2018, 01:55 AM   #1
B1p0larbear
Junior Member
 
Join Date: Jun 2018
Location: Texas
Posts: 5
iTrader: (0)
Default m42 misfire and smoking

Hello everyone, i have a 95ti with 275k mile. It has been running well for the past few months that i have owned it, every now and then the idle would stumble at a stop but overall okay. I left for work a few days back and had to hold the revs up to keep it running, but there was a noticeable misfire at all rpms. At this point i turned around and took the bike to work until I could mess with it over the weekend. So this weekend I started poking around, when started the idle is still very poor and this time i noticed smoke from the tailpipe, and a smell of raw fuel. I checked for signs of head gasket failure, now water in the oil, or oil in the water. At this point i pulled the plugs knowing i had a fresh set and they needed replacing anyway. Pulled all the plugs and all were dark black and smelled of fuel, also had 3 of 4 tubes saturated with oil. i replaced the plugs and reassembled, with that done i restarted the can and it is still running very poorly and smoking, but not quite stalling. If anyone has any ideas id love to hear them. thank you for reading
B1p0larbear is offline   Reply With Quote
Old 11-06-2018, 12:45 AM   #2
thenjnick
Junior Member
 
Join Date: Aug 2018
Location: Beachwood
Posts: 2
iTrader: (0)
Default

You need to replace your valve cover gasket. The oil is getting into your cylinders causing it to burn (hence the smoking exhaust) as well as your wet plugs/wires making it misfire.


Sent from my iPhone using Tapatalk
thenjnick is offline   Reply With Quote
Old 11-06-2018, 02:00 AM   #3
B1p0larbear
Junior Member
 
Join Date: Jun 2018
Location: Texas
Posts: 5
iTrader: (0)
Default

Thanks for the input, I was planning on ordering a valve cover set along with a new pcv valve. Figure that's as good a place to start as any. I'll keep you posted on the progress.
B1p0larbear is offline   Reply With Quote
Old 11-06-2018, 03:02 PM   #4
thenjnick
Junior Member
 
Join Date: Aug 2018
Location: Beachwood
Posts: 2
iTrader: (0)
Default

Pretty common replacement, mine is starting to seep into the cylinders too, good luck.


Sent from my iPhone using Tapatalk
thenjnick is offline   Reply With Quote
Old 11-09-2018, 08:23 AM   #5
318tiFatherFigure
Junior Member
 
Join Date: Nov 2018
Location: Perth Western Australia
Posts: 10
iTrader: (0)
Default

I doubt it is the valve cover gasket. I would be more looking at valve stem seals or a piston ring problem. Leaking injectors will cause rich running. Check all the vacuum hoses too. Excess crankcase pressure would force oil where you don't need it
If the fuel filter is old it could restrict pressure or allow dirt to jam the injectors open.
Hope some of the ideas strike a chord
318tiFatherFigure is offline   Reply With Quote
Old 11-24-2018, 09:12 PM   #6
B1p0larbear
Junior Member
 
Join Date: Jun 2018
Location: Texas
Posts: 5
iTrader: (0)
Default

Sorry it taken me so long to get back to this, but haven't had a chance to work on it in a while. So I've put the new pcv in, it had come apart. I cleaned out the intake and the pcv passages, and cleaned out the spark plug tubes. Then when for a test drive and found no improvement, in fact it is now backfiring along with the miss, but the smoke is reduced but not gone. At this point I think I'll search checking compression and leak down.


Just finished my compression check. Looks like I hurt cylinder 1, it is at 145 psi while other cylinders are in the 180 psi ballpark. Also have new plugs very black after about 5 miles but that could just be the oil I was burning with the broken pcv.

Last edited by B1p0larbear; 11-24-2018 at 09:53 PM.
B1p0larbear is offline   Reply With Quote
Old 12-02-2018, 12:09 AM   #7
B1p0larbear
Junior Member
 
Join Date: Jun 2018
Location: Texas
Posts: 5
iTrader: (0)
Default

Spent another day looking at her today, inspected and replaced all questionable vacuum lines. I removed the spark plugs again and found them dripping with fuel and with the injectors out I could see a pool of fuel on top of the intake valve for cylinder 1. So possibly failed injectors, or bad o2 sensor.
B1p0larbear is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 03:54 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2018, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 79.97 k/95.15 k (15.95%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.