318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Maintenance

Notices

Maintenance Service Interval questions, oil change info.

.
» Recent Threads
WTB: BavAuto Rubber...
Yesterday 05:49 PM
Last post by FunElan
Yesterday 05:49 PM
0 Replies, 92 Views
New Aussie 318ti owner
03-18-2020 06:29 AM
Last post by runnr548
Yesterday 03:14 PM
2 Replies, 483 Views
WTB: Drivers Side...
02-10-2020 07:39 PM
Last post by joe1602
07-09-2020 06:42 PM
1 Replies, 1,160 Views
318ti parts
06-09-2020 12:00 AM
Last post by joe1602
07-09-2020 06:39 PM
6 Replies, 1,353 Views
TPS and ICV signals on...
07-01-2020 07:06 PM
Last post by paul somlo
07-07-2020 05:43 PM
6 Replies, 844 Views
Ultimate Supercharger...
06-23-2019 08:06 AM
Last post by Z3nki
07-07-2020 02:54 PM
117 Replies, 114,983 Views
_-_Door Panel/Cards...
09-24-2011 03:17 PM
Last post by BMW_Hatchback
07-05-2020 10:48 PM
103 Replies, 22,057 Views
free door card (+...
03-27-2020 01:07 AM
Last post by sortasorted
07-03-2020 06:05 PM
7 Replies, 2,030 Views
M44 Lower Timing Chain...
05-25-2020 05:17 AM
Last post by 96318ticali
07-02-2020 09:44 PM
4 Replies, 1,015 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 06-16-2019, 06:57 AM   #1
MisterM52
Member
 
MisterM52's Avatar
 
Join Date: Jul 2017
Location: Stuttgart, Germany
Posts: 99
iTrader: (0)
Default Rusty coolant

I noticed the last owner or the one before him must had ran some straight water, when I drained the radiator and block I noticed a lot of corrosion, surface rust in the coolant passages and pipes.

So I was wondering if anyone here had some ideas? one idea was to run baking soda or vinegar for 10-20 mins and then flush that, I have distilled water here. I know some folks have used wood varnish and all, but I wanted to check with you guys, as this is my first M44 and I dont want anything to go attack other engine components eg. head gasket or anything because I ran vinegar or anything like that.

ideas?
MisterM52 is offline   Reply With Quote
Old 06-18-2019, 01:04 PM   #2
MisterM52
Member
 
MisterM52's Avatar
 
Join Date: Jul 2017
Location: Stuttgart, Germany
Posts: 99
iTrader: (0)
Default

So I ran vinegar for a bit, ran it, left it there overnight, drove it a bit. I had about 3L of vinegar in there, rest was distilled water. The drained water vinegar mixture was a bit rusty.

Then I neutralized the remainder vinegar by using some baking soda, I used 4 tea spoons, should had used half that. foamed up quick and at one point was quite pressurized as expected and the little bleeding screw hole became a volcano at operating temps. I then proceeded to clean it up with tap water from the hose, about 20L of that later, what came out was just as clean as what went in. At this stage I was done and added distilled water + green nulon coolant. bleed it. Hopefully this takes care of it.
MisterM52 is offline   Reply With Quote
Old 06-22-2019, 12:57 AM   #3
BRADESTAR
Senior Member
 
Join Date: May 2013
Location: Seattle
Posts: 487
Vehicles
iTrader: (0)
Default

I had similar situation. unbolted the head drain plug and thought "crap I unbolted the wrong bolt", cause nothing came out. Had to poke in there to get it to flow it had rusted over so.

I did the vinegar, but just through the head bit with everything off. I used a pipe cleaner thing to reach what I could and flushed it all. So didn't run the diluted vinegar through the whole system. It was while I was replacing everything. That was 2013ish and my coolant is still Blue today.
BRADESTAR is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Overheating 202 Romoser.MD Engine 18 02-17-2011 08:23 PM
95 318ti coolant issue colacan Engine 2 11-03-2010 03:38 AM
coolant type question LostCause Engine 6 09-01-2010 02:05 AM
Disappearing coolant after overheating = blown head gasket? Eric Engine 22 08-09-2009 07:28 PM
Black Coolant adamud Engine 13 11-20-2007 01:49 AM


All times are GMT +1. The time now is 06:17 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2020, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 74.05 k/85.45 k (13.35%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.