318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Maintenance

Notices

Maintenance Service Interval questions, oil change info.

.
» Recent Threads
Rebuild M44 or S52 swap?
Yesterday 07:21 AM
Last post by ZEK
Yesterday 10:32 PM
1 Replies, 280 Views
FS: 1998 BMW 318ti...
11-25-2019 12:57 AM
Last post by doucy2
Yesterday 07:29 PM
5 Replies, 840 Views
Ultimate Supercharger...
06-23-2019 09:06 AM
Last post by Blindsparky
12-11-2019 04:38 AM
101 Replies, 63,662 Views
bc racing or KWs?
12-05-2019 02:48 AM
Last post by Z3nki
12-09-2019 05:41 AM
3 Replies, 618 Views
heater bowden cable fix...
02-25-2012 02:50 AM
Last post by Hotredti
12-09-2019 01:00 AM
16 Replies, 15,426 Views
FS: 17" Style 40 / FULLY...
12-05-2019 09:34 PM
Last post by Meller1
12-05-2019 09:34 PM
0 Replies, 345 Views
FS: Brake UPGRADE Thread...
12-05-2019 09:33 PM
Last post by Meller1
12-05-2019 09:33 PM
0 Replies, 210 Views
FS: E36 M3 OEM Mirrors
11-13-2019 05:39 PM
Last post by Meller1
12-05-2019 09:26 PM
1 Replies, 721 Views
DASC Inforation or parts
12-05-2019 01:15 PM
Last post by pvansickler
12-05-2019 07:38 PM
2 Replies, 285 Views
16 Style 18s set...
12-05-2019 06:35 AM
Last post by 95 clubsport nugget
12-05-2019 06:35 AM
0 Replies, 276 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 06-16-2019, 07:57 AM   #1
MisterM52
Member
 
MisterM52's Avatar
 
Join Date: Jul 2017
Location: Stuttgart, Germany
Posts: 98
iTrader: (0)
Default Rusty coolant

I noticed the last owner or the one before him must had ran some straight water, when I drained the radiator and block I noticed a lot of corrosion, surface rust in the coolant passages and pipes.

So I was wondering if anyone here had some ideas? one idea was to run baking soda or vinegar for 10-20 mins and then flush that, I have distilled water here. I know some folks have used wood varnish and all, but I wanted to check with you guys, as this is my first M44 and I dont want anything to go attack other engine components eg. head gasket or anything because I ran vinegar or anything like that.

ideas?
MisterM52 is offline   Reply With Quote
Old 06-18-2019, 02:04 PM   #2
MisterM52
Member
 
MisterM52's Avatar
 
Join Date: Jul 2017
Location: Stuttgart, Germany
Posts: 98
iTrader: (0)
Default

So I ran vinegar for a bit, ran it, left it there overnight, drove it a bit. I had about 3L of vinegar in there, rest was distilled water. The drained water vinegar mixture was a bit rusty.

Then I neutralized the remainder vinegar by using some baking soda, I used 4 tea spoons, should had used half that. foamed up quick and at one point was quite pressurized as expected and the little bleeding screw hole became a volcano at operating temps. I then proceeded to clean it up with tap water from the hose, about 20L of that later, what came out was just as clean as what went in. At this stage I was done and added distilled water + green nulon coolant. bleed it. Hopefully this takes care of it.
MisterM52 is offline   Reply With Quote
Old 06-22-2019, 01:57 AM   #3
BRADESTAR
Senior Member
 
Join Date: May 2013
Location: Seattle
Posts: 453
Vehicles
iTrader: (0)
Default

I had similar situation. unbolted the head drain plug and thought "crap I unbolted the wrong bolt", cause nothing came out. Had to poke in there to get it to flow it had rusted over so.

I did the vinegar, but just through the head bit with everything off. I used a pipe cleaner thing to reach what I could and flushed it all. So didn't run the diluted vinegar through the whole system. It was while I was replacing everything. That was 2013ish and my coolant is still Blue today.
BRADESTAR is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Overheating 202 Romoser.MD Engine 18 02-17-2011 09:23 PM
95 318ti coolant issue colacan Engine 2 11-03-2010 04:38 AM
coolant type question LostCause Engine 6 09-01-2010 03:05 AM
Disappearing coolant after overheating = blown head gasket? Eric Engine 22 08-09-2009 08:28 PM
Black Coolant adamud Engine 13 11-20-2007 02:49 AM


All times are GMT +1. The time now is 10:01 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2019, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 73.97 k/85.42 k (13.41%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.