318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Maintenance


Maintenance Service Interval questions, oil change info.

» Recent Threads
New tuning options
09-28-2010 05:21 PM
Last post by gavin
12-03-2020 06:59 PM
17 Replies, 3,607 Views
CL 1996 318ti
11-29-2020 11:30 PM
Last post by dynagroove
12-03-2020 05:59 AM
2 Replies, 269 Views
FS 1995 Club Sport...
09-01-2020 03:34 AM
Last post by runnr548
12-03-2020 12:21 AM
1 Replies, 2,571 Views
FS 1996 318ti M sport...
09-03-2020 09:07 PM
Last post by runnr548
12-03-2020 12:16 AM
5 Replies, 4,348 Views
S52-Powered 1998 BMW...
11-15-2020 03:55 AM
Last post by runnr548
12-03-2020 12:05 AM
8 Replies, 1,863 Views
1997 318ti Active...
12-02-2020 04:26 AM
Last post by runnr548
12-02-2020 11:59 PM
1 Replies, 196 Views
Happy Birthday Tarjammer
12-01-2020 06:00 AM
Last post by 1996 328ti
12-01-2020 06:00 AM
0 Replies, 126 Views
Oil Filter Housing Leak...
02-14-2008 09:21 PM
Last post by joe1602
11-30-2020 01:32 PM
122 Replies, 108,453 Views
Making List of...
03-30-2005 07:14 AM
Last post by J!m
11-29-2020 01:30 AM
40 Replies, 37,806 Views
The 318ti OBD-II engine...
10-19-2006 07:48 PM
Last post by tylerjdoyle
11-28-2020 11:17 PM
159 Replies, 116,842 Views
Reply Share/Bookmark
Thread Tools Display Modes
Old 03-28-2020, 07:15 PM   #1
Junior Member
Join Date: Jun 2019
Location: Minnesota
Posts: 5
iTrader: (0)
Default Broken motor mounts caused engine to shift

Hey all,

(bold/italicized is the important stuff)

During my last rallyx event (October), I hit dropped down into a deep rut which caused my mounts to blow and an exhaust leak. I'm finally getting around the replacing them now that it's warm using the DIY on here (using a jack) however when I removed the driver side mount, I realized that both sides were in two parts and the engine had shifted to the driver side by about 1/2 an inch.

I removed the passenger side hoping this would allow the engine to move back over. It didn't. Rented an engine hoist this morning however when I pull the engine to the passenger side, it moves right back to where it was, off center.

I could recruit my roommate to lower the engine while I pull it into position however this doesn't solve the root problem - why won't the engine stay in the correct position when moved? If I lower it onto the mounts, will the pressure from the engine trying to pull itself toward the driver side cause the trans/engine mounts to fail prematurely? Do I need to disconnect the transmission as well?

Similar thread here: http://www.318ti.org/forum/showthrea...ht=motor+mount
tiRally is offline   Reply With Quote
Old 03-29-2020, 01:34 AM   #2
Senior Member
joe1602's Avatar
Join Date: Jan 2010
Location: Horseheads, NY
Posts: 251
iTrader: (0)

Disconnect the transmission mounts as well. You should not have to disconnect the transmission to change the motor mounts. By removing the transmission mounts it should give you enough play to maneuver the engine to get the mounts to line up correctly. You may need to get a second set of hands to help as well. You may also find the transmission mounts may have broken as well.
joe1602 is offline   Reply With Quote
Old 03-31-2020, 05:36 PM   #3
Junior Member
Join Date: Jun 2019
Location: Minnesota
Posts: 5
iTrader: (0)

Thanks Joe. I loosened up the trans mounts and crossmember and with the help of my roommate, was able to get the engine positioned.

Steps I took:
  1. Loosen the crossmember bolts and lower trans mounts nuts to allow more movement
  2. Driver side mount (bottom nut snug) - Person 1 pulls the hoist/engine over while person 2 checks if the stud lines up
  3. Person 2 slowly lowers the hoist while person 1 continues to hold it in position
  4. Put top nut on driver side mount just enough that it won't come off, jack hoist back up until passenger side mount will fit into place
  5. Person 1 holds mount into place (lined up correctly) while person 2 lowers the hoist
  6. Torque both sides to 33 ft/lbs and replace / tighten trans mounts and crossmember
tiRally is offline   Reply With Quote
Old 04-01-2020, 12:00 AM   #4
Senior Member
joe1602's Avatar
Join Date: Jan 2010
Location: Horseheads, NY
Posts: 251
iTrader: (0)

Sounds great! That is pretty much how I go about changing the motor mounts. I am hoping to put my solid mounts in my track car next week and will probably have to get my wife to help me line up the mounts!
joe1602 is offline   Reply With Quote


blown , motor , mount , shift

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Fun with math: determine engine displacement J!m Knowledge Base 1 06-24-2011 11:10 PM
TI DOWN: Engine Blew! HuGo Misc 43 05-24-2007 03:08 PM
bmw short shift ipswich318ti Transmission 12 11-13-2006 02:55 PM
I need an M44 Engine madfronter US and North America 15 05-18-2005 02:50 AM
M coupe/Z3 engine weights vs. M3 engine weight? 96cali Engine Swaps 19 11-03-2004 06:10 PM

All times are GMT +1. The time now is 12:04 PM.

Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2020, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 80.38 k/93.26 k (13.81%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.