318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Knowledge Base

Notices

Knowledge Base How to articles and things explained.

.
» Recent Threads
Which diff on 2.8 engine?
Today 01:06 AM
Last post by ZEK
Today 02:18 AM
1 Comments, 10 Views
Fixing yellow headlights...
09-19-2017 10:50 PM
Last post by bazar01
Today 01:46 AM
4 Comments, 202 Views
Euro glass headlights
09-24-2014 10:27 PM
Last post by apexspeedtech
Yesterday 11:17 PM
170 Comments, 84,456 Views
Died while flying down...
08-08-2017 10:23 PM
Last post by cpadil01
Yesterday 07:42 PM
5 Comments, 457 Views
96, M Sport, 5 speed,...
09-09-2017 07:24 PM
Last post by cjm1219
Yesterday 05:55 PM
10 Comments, 778 Views
97 with DASC
09-05-2017 03:12 PM
Last post by acs1775
Yesterday 05:51 PM
1 Comments, 409 Views
Happy Birthday Berni
Yesterday 05:00 AM
Last post by 1996 328ti
Yesterday 05:00 AM
0 Comments, 145 Views
1995 318ti Alaska Blue
08-14-2017 07:04 PM
Last post by runnr548
Yesterday 01:45 AM
1 Comments, 632 Views
Flat towing my 5 speed...
09-16-2017 10:22 PM
Last post by 1996 328ti
09-19-2017 03:50 PM
5 Comments, 439 Views
1995 Bmw 318ti $1000 or...
09-19-2017 03:45 PM
Last post by VitalyNinichuk
09-19-2017 03:45 PM
0 Comments, 143 Views
Comment Share/Bookmark
 
Tutorial Tools Display Modes
DIY - How to install an E36 X-Brace on your TI
DIY - How to install an E36 X-Brace on your TI
A nice suspension upgrade for a low price
Published by BlackBMWs
01-20-2015
Post DIY - How to install an E36 X-Brace on your TI

I have done a few of these on my TI's and have not really found a DIY on this easy upgrade.

I have found my E36 X-braces by watching the Pick & Pull for E36 convertibles and getting out there quickly. I have a impact wrench, sockets, rag and garbage bag I use for those retrievals.

For this simple DIY you will need:

Installation:
  • An E36 X-Brace
  • 6 BMW Nutserts
  • 6 M8 25mm bolts
  • 6 M8 washers

Tools:
  • 6 M8 1.50 Allen bolts (or regular M8 hex bolts)
  • 6 M8 nuts
  • 12 M8 washers
  • Red Loctite
  • 10mm open or ratcheting wrench
  • 8mm Allen socket and ratchet (or wrench if you are using a hex bolt
  • 13, 16mm sockets and ratchet/breaker bar
  • Ramps or stands
  • Floorjack
  • Drill with 7/16" bit
  • A file or rotary rasp to elongate the X-brace holes if needed
  • Handlight

An hour of time.

---------------------------------------------------------------------
Preperation:

Prep the six compression nuts (Nutserts) for installation.


I did mine shortly after taking this shot. If you have time for the Loctite red to harden, use way less. I prepped these the hour of the install. In retrospect, I'd use half the amount of Loctite next time around. Two of the six bolts locked up pretty well. Four of the bolts released just fine.


Installation:
  • Raise up front and chock rear tires.
  • Remove the lower plastic underpan if you have one installed
  • Using the 16mm socket and breaker bar, remove existing cross brace.



A light coat on the Nutsert to help it not spin after installation.


Drill out the subframe holes to accept the Nutsert. (I forgot to take a pic. )

Tighten the nut, not the Allen bolt. Make sure it's on tight, so the Nutsert won't spin. When the nut stops, you've crushed the Nutsert sufficiently. Reverse and extract the allen bolt.



Install the X-brace with the M8 bolts and washers on the subframe and the big bolts from the original subframe bar. I had to elongate the holes on the frame bar 1/8" to get the frame crossbar bolts to go in straight. I had to improvise with the bolts 5&6 (Center) with spares from the bolt bin.


Lower car, test drive and enjoy!
Tutorial Tools

  #1  
By eurohb on 01-20-2015, 08:24 PM
Default

Thank you! I will be doing this soon to my Ti so that i don't hurt the undercarriage !
Reply With Quote
  #2  
By mnguyen84 on 09-07-2017, 02:10 AM
Default

pictures are broken D:
Reply With Quote
  #3  
By BlackBMWs on 09-07-2017, 06:50 AM
Default

Yes, thank Photobucket.


Sent from my iPhone using Tapatalk
Reply With Quote
Comment

Bookmarks


Currently Active Users Viewing This Tutorial: 1 (0 members and 1 guests)
 
Tutorial Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Tutorial Tutorial Starter Category Comments Last Post
S54 engine into late model E36 swap (same 318ti) Hakentt-MS41.1 Engine Swaps 11 11-03-2015 04:08 PM
spotted: ti atrocity vsonix Lounge 33 04-22-2012 04:58 PM
Sold the wrong oil pan HELP! fast2002 Maintenance 4 01-27-2012 04:16 AM
Need a new nose panel. Can any e36 fit? RCV7 Exterior 16 03-22-2011 11:59 PM
E46 323 rotors to fit the ti? BMW_Hatchback Brakes 15 04-09-2008 04:31 PM


All times are GMT +1. The time now is 02:18 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2017, 318ti.org

Tutorial powered by GARS 2.1.8m ©2005-2006
© vBadvanced CMPS v3.2.2
[page compression: 72.46 k/87.38 k (17.07%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.