318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Knowledge Base

Notices

Knowledge Base How to articles and things explained.

.
» Recent Threads
98 MTech Daily Driver
12-01-2018 09:00 PM
Last post by KGB318TI
Yesterday 10:03 PM
1 Comments, 451 Views
Happy Birthday graymae
12-14-2018 06:00 AM
Last post by graymae
Yesterday 02:34 AM
1 Comments, 289 Views
m42 misfire and smoking
11-05-2018 01:55 AM
Last post by B1p0larbear
12-13-2018 11:11 PM
7 Comments, 1,385 Views
1996 318ti Part Out
09-13-2018 08:43 PM
Last post by Sbim
12-13-2018 07:12 AM
18 Comments, 3,507 Views
95 318ti in Albuquerque
12-11-2018 07:26 AM
Last post by dynagroove
12-13-2018 05:01 AM
6 Comments, 525 Views
MOD Request - Vote for...
12-12-2018 07:06 PM
Last post by 1996 328ti
12-13-2018 04:13 AM
1 Comments, 177 Views
Belt squeaking after...
11-27-2018 11:56 PM
Last post by BRADESTAR
12-12-2018 02:47 AM
6 Comments, 763 Views
FS: '98-Manual-169k...
12-11-2018 08:04 PM
Last post by Boston Green
12-11-2018 08:04 PM
0 Comments, 217 Views
WTB 5 speed 318ti, am...
12-11-2018 05:53 PM
Last post by KASZ
12-11-2018 05:53 PM
0 Comments, 158 Views
New here so lets arc you...
11-09-2018 08:56 AM
Last post by 318tiFatherFigure
12-11-2018 10:59 AM
2 Comments, 662 Views
Comment Share/Bookmark
 
Tutorial Tools Display Modes
Old 08-15-2006, 04:01 AM  
CirrusSR22
Senior Member
 
Join Date: Nov 2004
Location: Minneapolis
Posts: 1,585
iTrader: (3)
Default M42/44 / 318ti Valve Cover Gasket DIY. PICS!

* DIY * Replace the Valve Cover Gasket and Spark Plugs on the M42/44 Engine.

Parts Needed:

M42/M44 Valve Cover Gasket: 11121721876
Rubber Bolt Washers (15x): 11121721879
Spark Plug Hole Gasket w/Bolt Hole: 11121721475
Spark Plug...

Last edited by 1996 328ti; 10-12-2013 at 09:54 PM. Reason: Included M42.
CirrusSR22 is offline   Reply With Quote
  #90  
By aldogg7 on 10-23-2018, 03:38 AM
Default

Big bump for CirrusSR22's detailed write-up of this procedure with all of the pictures. Just did the whole thing on my M42 and it went flawlessly. Definitely a good time to replace the pair of cabin filters too. It looked like they had never been done on my 1995 TI.

And great advice from paul somlo on using a M6x1 nut to get the rubber washers on the valve cover bolts. I can't imagine having to use brute force to push those on 15 times.

The whole reason for doing this project is that a bit of oil was leaking into the coil tubes for cylinders 1-3. I cleaned out the oil and replaced the plugs (likely never had been done either) just before putting the new gasket and cover on.

Remember to use a criss-cross pattern when doing the cover bolts too. I started with the bolt in the very center at cylinder 2. It was actually this plug tube that had the most oil in it. It looked like the gasket had been replaced once before, and I bet that last time the surrounding bolts were put on first, leaving an curvature in the cover and a gap at the center bolt.

Anyway, fun job, hardest part was probably pulling the air flow baffle out. It might not be needed to be removed, but it certainly gives more room to maneuver the valve cover off and on.
Reply With Quote
  #91  
By Mikes318ti on 11-02-2018, 07:14 AM
Default

This DIY saved my car. 1997 318ti, so we'll dpne thank you so so much, last owner did some garbage work. Was nice to undo some of that work... I can't unscrew the over torqued bolt that stripped my head. But that's another problem. Thanks again for just being another awesome 318ti owner
Reply With Quote
  #92  
By 318tiFatherFigure on 11-12-2018, 09:08 PM
Default

My ti M-Pack has a blown head gasket - why I got it cheap.
One of my other cars is a Daimler Sovereign S2 - read Jaguar XJ6 S1.
The engines in them are renown for camshaft cover oil leaks - THE fix is a well kept secret.
When the retainers are over torqued the material of the head is drawn upwards preventing the cover from sitting down correctly. This is usually followed by some PO tightening down the retainers further - increasing the leak.
The trick is to LIGHTLY countersink the threaded holes to remove the distorted material.
New gaskets correctly installed and covers correctly torqued - no leaks.
Hope that helps some one with the leak that wont stop!
Last edited by 318tiFatherFigure; 11-12-2018 at 09:17 PM.. Reason: Extra info
Reply With Quote
  #93  
By mrmikkelsen on 11-13-2018, 03:25 AM
Default

I just did this, thanks for the preview walk through. That oil line grommet thing was rock hard and shattered when I took it out. Due to your heads up about it being hard as plastic, I stuffed rags all around it before pulling it off so all the brittle little bits were captured. My cabin air filters were downright nasty. See yours tucked back inside behind that ducting you removed at the rear. I ordered them Saturday and Amazon had there here Monday slipping them in just in time before I have to drive back to work tomorrow. I love it when a plan comes together! 12 years later and finally you know your pictures did some good. Thanks
Reply With Quote
Comment

Bookmarks


Currently Active Users Viewing This Tutorial: 1 (0 members and 1 guests)
 
Tutorial Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT +1. The time now is 06:52 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2018, 318ti.org

Tutorial powered by GARS 2.1.8m ©2005-2006
© vBadvanced CMPS v3.2.2
[page compression: 68.60 k/84.31 k (18.64%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.