318ti.org forum

Go Back   318ti.org forum > Classifieds > For Sale > US and North America

Notices

.
» Recent Threads
Happy Birthday ...
Yesterday 05:00 AM
Last post by 1996 328ti
Yesterday 05:00 AM
0 Replies, 151 Views
M52tub25 in 318ti
05-03-2019 03:48 AM
Last post by Starbursty2122
Yesterday 02:43 AM
1 Replies, 387 Views
Turner/Conforti M42 chip...
05-09-2019 04:46 AM
Last post by veritas137
05-23-2019 11:11 PM
1 Replies, 527 Views
DASC considering part out
05-04-2019 11:42 PM
Last post by Lysaimachus
05-23-2019 09:39 PM
6 Replies, 882 Views
new engine build. dasc +...
01-02-2016 01:28 AM
Last post by andakn
05-23-2019 07:09 PM
195 Replies, 100,172 Views
Rear strut brace
04-04-2014 04:39 AM
Last post by MisterM52
05-20-2019 09:48 PM
46 Replies, 15,595 Views
M44 strange water leak...
05-18-2019 09:01 AM
Last post by MisterM52
05-20-2019 09:46 PM
6 Replies, 506 Views
Fox well NT510 - service...
05-20-2019 07:27 PM
Last post by dudecati
05-20-2019 07:27 PM
0 Replies, 190 Views
FS: Complete Black Dash
05-20-2019 04:08 AM
Last post by KGB318TI
05-20-2019 04:08 AM
0 Replies, 287 Views
WTB: Black Dash and...
03-21-2019 03:28 AM
Last post by KGB318TI
05-20-2019 03:15 AM
1 Replies, 647 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 10-21-2011, 04:42 PM   #1
blefevre
Member
 
Join Date: Jan 2009
Location: Golden, CO
Posts: 45
iTrader: (0)
Default M44 DASC + extras - no shipping for now

I have a used M44 DASC Superchager kit for sale. I bought the kit used from bimmerforums a few years back. I think it had about 20k miles on it. I started making sure I had all the parts and started gathering any additional things I should replace while in there. I never got to install it. We are working on getting new cars so this won't be getting installed.

-M44 (96-99) that was on a 318ti. You will have to find out if it fits a sedan or an E30.
-What I believe is the full kit minus one 45-degree bend on the intake and the MAF brackets that support the intake. You can run without them or use something to brace it if you want. It's not needed according to downing.
-Extra fuel rail and injectors that can be sent to get cleaned a head of time
-boost gauge with pod/hoses
-new manifold gaskets
-new prelude air filter. Use this instead of the K&N so you can run a proper paper filter
-coolant hoses that attach to the block that always break anyways
-new accessory pullys
-new gatorback belt
-a few new pieces from DASC
-all new hoses
-check valve that adds about .5psi
-new hardware
-extra TB, I believe a M3 one
-air filter heat shield

I also have the install manual and parts list from DASC on .pdf.

$2,500
Local only for now, Denver CO

Autometer gauge pod for a Ti/Autometer boost gauge lines/Manifold gasket/Gatorback belt/New EGR relocation block


Supercharger/Manifold/Elbow/Misc stuff already attached. Save install time!


New hardware from fastenal and new pulley kits


New hoses. You will have to cut to length most of the hoses. I added up the BOM and bought what I needed. Comes with the used hoses as well. Lots of hoses!


Heat shield


Pulley brackets/New coolant pipes/boost gauge/ERG/RRFPR/Charger bracket/TB/TB cable/Fuel rail/Injectors/Check valve

Last edited by blefevre; 10-22-2011 at 12:45 AM.
blefevre is offline   Reply With Quote
Old 10-22-2011, 12:46 AM   #2
blefevre
Member
 
Join Date: Jan 2009
Location: Golden, CO
Posts: 45
iTrader: (0)
Default

New EGR block piece


Manifold


Elbow/Bypass valve


Supercharger


New pulleys
blefevre is offline   Reply With Quote
Old 10-23-2011, 05:27 PM   #3
blefevre
Member
 
Join Date: Jan 2009
Location: Golden, CO
Posts: 45
iTrader: (0)
Default

Please let me know if there would be interest if I opened this up to shipping. The buyer would have to pay for shipping + paypal fees though.
blefevre is offline   Reply With Quote
Old 10-25-2011, 04:40 AM   #4
blefevre
Member
 
Join Date: Jan 2009
Location: Golden, CO
Posts: 45
iTrader: (0)
Default

Sold
blefevre is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Vac leak on my M44 DASC @ injector base JP422 Induction 11 01-27-2011 06:13 PM
M44, DASC, 3.4 pulley, TT S3 tune, snow performance=> Kaboum ludo Induction 19 12-07-2009 11:56 AM
M42 - M44 DASC yoda Induction 13 09-04-2009 03:59 PM
M44 dasc work on m42??? nickmpower Induction 12 06-27-2009 06:05 PM
Differences in DASC for M42 and M44 lkwd318ti Induction 10 10-18-2007 07:38 AM


All times are GMT +1. The time now is 05:53 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2019, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 76.49 k/88.99 k (14.05%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.