318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Engine Swaps

Notices

Engine Swaps Engine conversions.

.
» Recent Threads
1996 5 speed feeler.
10-06-2018 05:30 PM
Last post by bazar01
Today 11:41 AM
2 Replies, 335 Views
Looking for running...
Today 03:06 AM
Last post by HellrotRuss
Today 03:06 AM
0 Replies, 77 Views
Oil Pan Cleaning
10-12-2018 02:46 AM
Last post by ZEK
Yesterday 04:15 AM
3 Replies, 444 Views
NEED TO BUY BLACK SHIFT...
Yesterday 03:29 AM
Last post by Estii
Yesterday 03:29 AM
0 Replies, 86 Views
New ti owner from Chicago
10-12-2018 09:28 PM
Last post by BRADESTAR
Yesterday 02:49 AM
4 Replies, 342 Views
Bucking, loss of power...
10-11-2018 09:18 PM
Last post by BRADESTAR
Yesterday 02:45 AM
1 Replies, 312 Views
Overheating / thermostat...
10-08-2018 07:27 PM
Last post by paul somlo
10-12-2018 08:16 PM
11 Replies, 606 Views
Driveshaft tunnel liner?
10-10-2018 06:04 AM
Last post by BRADESTAR
10-11-2018 04:39 AM
3 Replies, 440 Views
Just replaced Fuel...
10-08-2018 09:44 PM
Last post by spidertri
10-10-2018 07:41 PM
1 Replies, 364 Views
Happy Birthday amiller07
10-10-2018 05:00 AM
Last post by 1996 328ti
10-10-2018 05:00 AM
0 Replies, 274 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 08-03-2018, 04:15 AM   #16
Projectvoltron
Junior Member
 
Join Date: May 2018
Location: Colorado
Posts: 14
iTrader: (0)
Default

Quote:
Originally Posted by spidertri View Post
My M44/getrag didn't have a CDV so you may not need the delete. I did all that stuff except for the lower temp tstat and coolant sensor, what's the benefit of those? I didn't know they made a lower temp sensor.

I had to have a friend machine the tstat housing flat so that it would seal correctly. The cheap housings all come from china and are cast aluminum. It's good to clean up the casting flash inside too.

I used stock exhaust manifolds to the OBD2 midpipe and then a Z3 3.0i catback, had to cut it down slightly but the exhaust hangers all lined up.

Awesome! That's good to know!

As far as clutch is concerned. Do you guys have any opinions on a decent cheap option? Is the valeo kit a decent kit?
Projectvoltron is offline   Reply With Quote
Old 08-16-2018, 02:38 AM   #17
Kglenn328
Junior Member
 
Join Date: Aug 2018
Location: Indiana
Posts: 3
iTrader: (0)
Default

So would you guys know where I could get some info about swapping a 97m52b28 into a 95 318ti I have the whole doner car still and will keep it till everything is good with the ti but I'm concerned about obd1 car with obd2 motor and the ews as well it's my first swap in a bmw but I can tell getting the motor in is the easy part
Kglenn328 is offline   Reply With Quote
Old 09-07-2018, 02:22 AM   #18
Projectvoltron
Junior Member
 
Join Date: May 2018
Location: Colorado
Posts: 14
iTrader: (0)
Default

I should be commencing my swap next week. I got all the parts I needed ordered. I have my swap car lined up and the 318ti waiting a new transplant.

Iím getting pretty excited about it all. Iím goint to do a lot of stuff to the motor while itís out like
Sap delete
M50 manifold with the bimmerworld swap kit
New silicone elbow
Aluminum radiator
Silicone coolant lines
New water pump
Vanos rebuild with tools
Asc delete plug
Iím trading some Audi wheels for a stage 4 clutch kit (kinda way to aggressive)
Fan delete kit
New coolant tank
Bought a dme with sap delete, rear o2 delete, ews delete, etc

Is there anything Iím forgetting that you guys can think of?

Thanks again for all the help and support!
Projectvoltron is offline   Reply With Quote
Old 09-20-2018, 03:59 AM   #19
Projectvoltron
Junior Member
 
Join Date: May 2018
Location: Colorado
Posts: 14
iTrader: (0)
Default

Quote:
Originally Posted by spidertri View Post
I had to read the wire diagrams, wiring is not my strong point either, lol. No pictures unfortunately, I had to get it done quickly so my car would pass inspection. When I finally have a need to pull the engine apart I'm probably going to install a manual M52 wiring harness, it bothers me to have the auto trans stuff just hanging around in there.

In the wiring harness X20 connector, I had to add pin 10, that is the signal to the reverse light plug. And then in the plastic box of wires that sits over the engine, there is a junction in there that I spliced the power wire for the reverse light switch into. If you trace pin 22 from the X20 to the plastic box, that is what I spliced into.

No you don't need the TCU, that and the associated wiring just gets ignored.
So I am balls deep in the swap right now and I am a little confused on what to do with the reverse light. from what I understand this is what I need to do.
Cut the 2 plug connector off either the Auto harness or the old M44 manual harness. Run one wire from pin 10 on the x20 and run the other wire from the box above the engine and connect it to the wire that comes off of pin 22 of the x20

Please let me know if I am wrong.

Also I ran into another problem. What do I do with the x69 Connector off the auto harness. My 318ti Doesn't have a X69 connector. It only has the x20 and the x6031 connector. If someone could help me out with that I would greatly appreciate it. Thank you
Projectvoltron is offline   Reply With Quote
Old 09-25-2018, 08:29 PM   #20
spidertri
Senior Member
 
spidertri's Avatar
 
Join Date: Apr 2007
Location: Elizabeth City, NC
Posts: 3,831
Vehicles
iTrader: (9)
Default

Sounds like what I did, it was a while ago but yeah. Did you get it to work?

My car had the x69 so I can't help there, did you find any threads talking about it here or on bf.c?
__________________
~Dave~

98 328ti Morea Grun slicktop
13 JGC WK2 Deep Cherry

Search | RealOEM
spidertri is offline   Reply With Quote
Old 09-25-2018, 08:42 PM   #21
Projectvoltron
Junior Member
 
Join Date: May 2018
Location: Colorado
Posts: 14
iTrader: (0)
Default

Quote:
Originally Posted by spidertri View Post
Sounds like what I did, it was a while ago but yeah. Did you get it to work?

My car had the x69 so I can't help there, did you find any threads talking about it here or on bf.c?
I havenít gotten that far. I have posted on bummer forums and here looking for an answer by havenít found anything.

Iím also waiting on a clutch to come in.

Was your ti originally a auto or manual?
Projectvoltron is offline   Reply With Quote
Old 09-26-2018, 07:01 PM   #22
spidertri
Senior Member
 
spidertri's Avatar
 
Join Date: Apr 2007
Location: Elizabeth City, NC
Posts: 3,831
Vehicles
iTrader: (9)
Default

Mine is a '98 manual ti with engine from a '97 auto 328i.
__________________
~Dave~

98 328ti Morea Grun slicktop
13 JGC WK2 Deep Cherry

Search | RealOEM
spidertri is offline   Reply With Quote
Old 09-26-2018, 10:25 PM   #23
Projectvoltron
Junior Member
 
Join Date: May 2018
Location: Colorado
Posts: 14
iTrader: (0)
Default

Quote:
Originally Posted by spidertri View Post
Mine is a '98 manual ti with engine from a '97 auto 328i.
I wonder why my 97 ti doesnít have one then. Thatís crazy and very confusing
Projectvoltron is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
97 M44 to 97 M52 swap questions Octarine Engine Swaps 5 02-21-2014 12:46 PM
M Roadster Suspension Swap (front and rear subframes, brakes, etc) questions Ragnorak Suspension 7 01-11-2013 04:29 PM
E30 Diff and Axle swap questions pred Differentials 2 08-14-2012 08:54 PM
M52 swap questions??? Diamon7 Engine Swaps 3 12-16-2011 01:30 AM
questions for the swap people Jean H.318TI Engine Swaps 17 10-29-2010 03:30 AM


All times are GMT +1. The time now is 02:24 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2018, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 98.20 k/115.41 k (14.91%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.