318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Engine

Notices

Engine Tuneups, chips, wires, spark plugs.

.
» Recent Threads
Learning to drift
06-29-2019 09:11 PM
Last post by andakn
Yesterday 01:34 PM
1 Replies, 592 Views
Ultimate Supercharger...
06-23-2019 08:06 AM
Last post by thenjnick
07-20-2019 11:34 PM
60 Replies, 6,105 Views
Knock Sensor Error &...
07-07-2019 05:42 AM
Last post by thenjnick
07-20-2019 04:12 PM
10 Replies, 784 Views
Rudolph the Red 318ti
05-06-2019 10:49 PM
Last post by MisterM52
07-20-2019 03:44 AM
28 Replies, 5,355 Views
Help on replacing ‘96...
07-19-2019 04:11 PM
Last post by Denteen
07-19-2019 08:22 PM
2 Replies, 323 Views
M44 Supercharged Project...
04-07-2019 06:54 AM
Last post by steve f
07-19-2019 01:46 AM
9 Replies, 1,924 Views
Oil Filter Housing Leak...
02-14-2008 08:21 PM
Last post by shriberone
07-18-2019 09:59 PM
119 Replies, 85,162 Views
H&R Race springs and...
06-26-2019 09:46 AM
Last post by Denteen
07-18-2019 12:07 AM
1 Replies, 808 Views
97' M-Tech Edition...
08-30-2018 06:51 PM
Last post by dudecati
07-17-2019 11:06 PM
13 Replies, 3,323 Views
1996 332ti supercharged...
06-08-2019 08:27 PM
Last post by slowoldpoop
07-16-2019 07:59 PM
6 Replies, 1,944 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 01-12-2019, 08:31 AM   #1
318tiFatherFigure
Junior Member
 
Join Date: Nov 2018
Location: Perth Western Australia
Posts: 21
iTrader: (0)
Default Just Changed My Head Gasket

I bought the car with this known problem. It turned out the head was cracked in 8 places - 2 to each of the 4 inner exhaust valves.

This appears to have been caused by the radiator fan switch failing.

Also when tightening down the head the centre 6 bolts when rechecked prior to the next stage were found to be slacker than they should have been. I re-torqued all the bolts to that first stage. The outer 4 had not changed.

The other problem was the idle control valve had jammed. That was released with a small screwdriver and loads of WD-40.

The oil and filter were changed and run for about 30miles then both changed again. Lots of debris collected.

Hope these pointers help someone else.

Last edited by 318tiFatherFigure; 01-12-2019 at 09:12 AM.
318tiFatherFigure is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Blown head gasket with a big suprise robnhod Engine 5 10-15-2015 09:32 AM
Head gasket go boom ..... blowin 4 Engine 76 04-07-2013 09:29 AM
M42 overheating after head gasket AlphaVortex Engine 10 04-26-2011 05:23 PM
Blown Head Gasket Detection Recon427 Engine 12 02-21-2010 02:30 AM
Why not install a Cometic head gasket (pics) dave45056 Engine 0 07-04-2008 03:26 PM


All times are GMT +1. The time now is 12:04 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2019, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 63.91 k/73.45 k (13.00%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.