318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Maintenance

Notices

Maintenance Service Interval questions, oil change info.

.
» Recent Threads
1998 slicktop hellrot...
03-14-2021 08:40 AM
Last post by anassa
Today 06:07 AM
5 Replies, 1,493 Views
Differential parts...
12-11-2009 03:53 AM
Last post by mb0686
04-10-2021 09:28 PM
125 Replies, 97,904 Views
Cat got stolen, looking...
04-09-2021 06:27 PM
Last post by Pier
04-09-2021 06:27 PM
0 Replies, 118 Views
Happy Birthday snuggz
04-07-2021 05:00 AM
Last post by 1996 328ti
04-07-2021 05:00 AM
0 Replies, 152 Views
1997 Black 318ti 5spd...
03-28-2021 09:11 PM
Last post by jwm
04-05-2021 11:44 PM
3 Replies, 869 Views
Installing Thule Roof...
02-08-2010 06:06 PM
Last post by canduc
04-05-2021 08:44 PM
10 Replies, 29,818 Views
Fuel pressure/Fuel trims...
04-05-2021 04:13 AM
Last post by ilillund83
04-05-2021 04:13 AM
0 Replies, 296 Views
Happy Birthday M5Yates
04-04-2021 05:00 AM
Last post by 1996 328ti
04-04-2021 05:00 AM
0 Replies, 428 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 11-17-2018, 03:56 AM   #1
S.W.B.C
Junior Member
 
Join Date: Dec 2009
Location: Oregon
Posts: 17
iTrader: (0)
Default SIR crankshaft tool

Grasping at straws but anyone in the Portland area that has the SIR tool for securing harmonic balancer for removing the crankshaft bolt? Rent , barter, or trade for beer or???
Thanks so much!!!!!
Silas
S.W.B.C is offline   Reply With Quote
Old 11-24-2018, 03:20 AM   #2
paul somlo
Senior Member
 
Join Date: Sep 2006
Location: Greeley CO
Posts: 222
iTrader: (0)
Default

I use a pin to lock the flywheel - the tip is 0.307 diameter and 0.392 in length, the next section is 0.452 in diameter and 1.577 inches in length. The next larger section doesn't matter.

You might get away using a 5/16" drill bit or an 8mm bolt.

I was concerned that I'd be stressing the crankshaft, but I've used it several times now with no ill effects, and I've read accounts of others doing likewise.
Attached Thumbnails
Click image for larger version Name:	PB232533.JPG Views:	46 Size:	84.9 KB ID:	17417  
paul somlo is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
crankshaft pulley holding tool rbush Engine 16 02-28-2016 08:36 PM
Misc parts FS: M44 Crank Locking Pin/Dowel Tool for Head repair 96silver318ti Parting out & Parts (US) 4 08-22-2013 10:58 PM
DIY: R&R crankshaft position sensor elfhearse Knowledge Base 4 05-12-2010 03:24 AM
MemoScan B200 SRS/Airbag Tool CirrusSR22 Maintenance 6 05-30-2009 07:21 PM
Source for rear subframe bushing tool. bullmand Suspension 7 12-13-2007 04:07 PM


All times are GMT +1. The time now is 07:42 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2021, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 65.49 k/75.65 k (13.43%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.