318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Engine Swaps

Notices

Engine Swaps Engine conversions.

.
» Recent Threads
1999 M-Sport For Sale
12-31-2023 05:10 PM
Last post by Coop540iT
03-23-2024 06:39 PM
1 Replies, 101,433 Views
Once again 318ti owner...
03-20-2024 12:39 PM
Last post by two30grain
03-22-2024 02:04 PM
1 Replies, 64,467 Views
What brakes do I...
03-20-2024 03:27 PM
Last post by huirtera
03-20-2024 03:27 PM
0 Replies, 61,651 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 10-20-2019, 01:25 AM   #1
ilillund83
Junior Member
 
Join Date: Jun 2009
Location: California
Posts: 15
iTrader: (0)
Default S52 swap EVAP question

Hi guys, I have a 98 ti that I recently swapped a 98 s52 into with the help of J!ms guide and lots of good info here on the site. Anyhow, everything is up and running great but I am having an issue with my readiness monitors specifically EVAP and SAP. Also I am getting code p1403- Charcol Filter Shutoff Valve. I am looking for any input I can get, I assumed that both cars used the same charcoal can located near the gas tank and hooked the purge valve coming from the intake to the blue line running to the rear of the car. Is this correct or did the ti use one of the older round cans? Do I need to dig up an s52 canister? BTW I know that I can have the dme flash these out but would really rather get things hooked up correctly if possible. I plan on taking this to the smog ref to get my swap sticker and dont want to worry about having a flashed dme throw a red flag. -Thanks all, Ian
ilillund83 is offline   Reply With Quote
Old 10-20-2019, 10:10 PM   #2
ilillund83
Junior Member
 
Join Date: Jun 2009
Location: California
Posts: 15
iTrader: (0)
Default

I found this on real oem,
https://www.realoem.com/bmw/enUS/sho...diagId=16_1034

I see that 97 was the cutoff but cant find any info on 98+ ti's. Do they share the same e36 sedan/coupe Charcoal filter/valve (the plastic box) near the fuel tank? I have been under looking for it and looked for access in the rear hatch floor but I dont see anything.

If anyone knows or has any knowledge relating to the charcoal filter on 98+ ti's or code p1403 on s52 engines that they could share I would really appreciate it. Thx all
ilillund83 is offline   Reply With Quote
Old 10-21-2019, 01:06 AM   #3
BRADESTAR
Senior Member
 
Join Date: May 2013
Location: Seattle
Posts: 513
Vehicles
iTrader: (0)
Default

I think your set up is correct. Do you know that the Ti wasn't throwing this code before the swap? Maybe a line is clogged, or something like that.
BRADESTAR is offline   Reply With Quote
Old 10-21-2019, 05:26 AM   #4
ilillund83
Junior Member
 
Join Date: Jun 2009
Location: California
Posts: 15
iTrader: (0)
Default

Yeah to my knowledge everything was good with the smog equipment prior to swap. Never a CEL or anything. I did some more digging around and found that yes indeed the later TI's have the plastic box style charcoal filter shared with other e36s it was located on the driver's side rear seat side panel behind another access panel. I had seen the suggestion to blow air through each of the disconnected lines and filter on the m3forum so I went ahead and gave it a try. No codes thus far, going to give it a few cycles and hope it readies up. I will report back as soon as I know if all's well.
ilillund83 is offline   Reply With Quote
Old 10-23-2019, 10:14 PM   #5
ilillund83
Junior Member
 
Join Date: Jun 2009
Location: California
Posts: 15
iTrader: (0)
Default

After 3 days of light driving my CEL light is back on with P1403 and my readiness monitors for SAP and EVAP are still not set. I swapped breather valves with the donor car, used compressed air to blow out the lines and checked all connections. Any ideas?

I am almost to the last resort of having my DME reprogrammed to delete EVAP/SAP and set to ready. Does anyone have any experience with this and passing with a CA smog ref?

Thanks all, Ian
ilillund83 is offline   Reply With Quote
Old 10-29-2019, 11:02 PM   #6
ilillund83
Junior Member
 
Join Date: Jun 2009
Location: California
Posts: 15
iTrader: (0)
Default

Thank you to Trusted-1 on this forum, this issue is finally solved. P1403 was cleared and ecu readiness has set. Can be solved by double checking the pinout's on the harness's as indicated on the last post of this thread http://www.318ti.org/forum/showthread.php?t=42041 .
ilillund83 is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
NJ '97 318ti w/ S52 swap - Selling as parts/project car or Parting out Hawkster Cars for Sale 3 05-02-2018 01:25 PM
S52 swap question msbmw740il United States 2 06-09-2016 05:24 PM
WI Feeler: 318ti S52 swap alexw Cars for Sale 4 06-15-2014 05:46 AM
New Member s52 Swap cnaville210 Engine Swaps 34 08-05-2012 11:22 PM
S52 OBDII to OBDI M50 Manifold Swap DYI dahamler Engine Swaps 42 09-18-2011 02:33 PM


All times are GMT +1. The time now is 01:03 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 77.29 k/90.50 k (14.60%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.