318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Engine

Notices

Engine Tuneups, chips, wires, spark plugs.

.
» Recent Threads
FS: 1996 318ti m-sport...
Today 02:31 AM
Last post by Mad A
Today 02:31 AM
0 Replies, 115 Views
FS - Adjustable Front...
01-26-2019 11:30 PM
Last post by E36Shua
Yesterday 04:01 PM
7 Replies, 4,410 Views
Looking for 97-98 318ti...
08-03-2020 07:29 PM
Last post by Mad A
Yesterday 03:44 PM
3 Replies, 500 Views
318ti S52 ZF 5speed
Yesterday 01:08 PM
Last post by E36Shua
Yesterday 01:10 PM
1 Replies, 106 Views
Big brake adapter...
08-12-2020 05:10 PM
Last post by Beam318i
08-12-2020 11:02 PM
2 Replies, 213 Views
97 BMW 318ti (California...
08-12-2020 10:21 PM
Last post by Texas98ti
08-12-2020 10:21 PM
0 Replies, 79 Views
96 M-Sport Slick-Top
08-05-2020 07:34 PM
Last post by runnr548
08-11-2020 10:25 PM
6 Replies, 675 Views
parting out a nice 95...
05-16-2020 10:27 PM
Last post by Scott1283
08-11-2020 09:58 PM
11 Replies, 4,086 Views
318ti Alaska Blue shell,...
08-11-2020 08:11 PM
Last post by David325is
08-11-2020 08:11 PM
0 Replies, 83 Views
wtb 4.45 lsd
08-08-2020 11:37 PM
Last post by joek84
08-08-2020 11:37 PM
0 Replies, 524 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 05-25-2020, 05:17 AM   #1
96318ticali
Junior Member
 
Join Date: Aug 2013
Location: Florida
Posts: 23
iTrader: (0)
Question M44 Lower Timing Chain Gasket

Is it possible to only replace the lower timing chain cover gasket? About 2 yrs. ago I replaced the cylinder head which required replacing the upper chain cover gasket. The lower wasn't leaking so I left it alone. Now the lower is leaking and I would like to keep its gasket replacement as simple as possible. Also, is it possible to remove the lower cover without removing the water pump? The last time I removed a water pump on a ti the bolt hole ears broke so I don't want to risk that if possible. Any info is appreciated!
96318ticali is offline   Reply With Quote
Old 07-01-2020, 07:02 PM   #2
paul somlo
Senior Member
 
Join Date: Sep 2006
Location: Greeley CO
Posts: 217
iTrader: (0)
Default

I'm not sure that you'll be able to buy the lower gasket without the upper one integral with it - you may have to do some cutting, which may leave gaps. I recently chased some oil leaks that I'd been plagued with for over a decade - I decided to delete the upper and lower cover gaskets, as well as the gasket for thermostat and water pump, used Permatex Ultra Grey instead.

I've seen pictures of the lower cover off with the water pump still installed, but I couldn't remove my cover with the water pump in place.
paul somlo is offline   Reply With Quote
Old 07-02-2020, 04:57 PM   #3
96318ticali
Junior Member
 
Join Date: Aug 2013
Location: Florida
Posts: 23
iTrader: (0)
Default

Thanks for your reply. I have also seen a picture with the water pump installed and the lower cover removed. I will probably do both top and bottom covers and be done with it.
96318ticali is offline   Reply With Quote
Old 07-02-2020, 05:54 PM   #4
paul somlo
Senior Member
 
Join Date: Sep 2006
Location: Greeley CO
Posts: 217
iTrader: (0)
Default

The area that's the most leak prone is where the two rubber profile gaskets butt up against each other - use lots of RTV in that area. And that's regardless of whether you use the factory metal gaskets or delete them. The other area, of course, is the very bottom of the timing case, where oil pools. One of my failed attempts included the factory gaskets and blue Hylomar. I've read about people using the factory gaskets in conjunction with RTV, also. It seems that the tensioner side is more leak prone than the other side - when I had mine open, the driver's side of the case was fairly dry, just the way the oil distributes itself, I suppose.

If you do the top cover, you'll probably need to loosen or remove the valve cover, for reassembly. You probably already know this, but you can use two of the bolts that fasten the water pump to extract it, via the threaded holes in the case. 1/4 - 1/2 turn at a time for each bolt should get the pump out without breakage, go slow. I've heard of people breaking pumps, but I've been lucky, they always come out easy.
paul somlo is offline   Reply With Quote
Old 07-02-2020, 09:44 PM   #5
96318ticali
Junior Member
 
Join Date: Aug 2013
Location: Florida
Posts: 23
iTrader: (0)
Default

Years ago I replaced both covers on my son's ti and I broke the water pump. I was just hoping to reduce the amount of work required by only doing the bottom. I appreciate your insights and suggestions. Thanks!
96318ticali is offline   Reply With Quote
Reply

Bookmarks

Tags
leaking timing cover , lower timing cover , oil leak , timing chain cover , timing cover removal


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Anyone here replaced your timing chain tensioner for your M44? stringdimensions Maintenance 0 01-23-2020 02:19 AM
DIY: Timing Case Cover Gaskets and Chain Guides CirrusSR22 Knowledge Base 23 10-31-2017 06:54 PM
M44 Timing case profile gasket?? E36Fiend4130 Engine 0 05-05-2017 12:52 AM
318ti use Z3 DME for SAP delete and emissions delete new318tifan Engine 5 02-03-2016 03:24 PM
WTB: Early Lower Timing Chain Cover e36Vertrag US and North America 0 03-16-2009 05:07 AM


All times are GMT +1. The time now is 05:29 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2020, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 79.79 k/93.12 k (14.32%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.