318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Maintenance

Notices

Maintenance Service Interval questions, oil change info.

.
» Recent Threads
1999 M-Sport For Sale
12-31-2023 05:10 PM
Last post by Coop540iT
03-23-2024 06:39 PM
1 Replies, 98,911 Views
Once again 318ti owner...
03-20-2024 12:39 PM
Last post by two30grain
03-22-2024 02:04 PM
1 Replies, 61,818 Views
What brakes do I...
03-20-2024 03:27 PM
Last post by huirtera
03-20-2024 03:27 PM
0 Replies, 59,122 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 10-16-2018, 01:24 PM   #166
weste46
Junior Member
 
Join Date: Aug 2018
Location: Indiana
Posts: 21
iTrader: (0)
Default

Also, I forgot to add that the water pump had already been done before, but it did not want to come out. I had to make a puller tool after I broke off both sides of the casting when trying to use the threaded holes to push the pump away from the block.

Attached is the tool I made out of an old prybar, with tapped 1/2" holes. It was flat when I made it, the water pump was really in there.
Attached Thumbnails
Click image for larger version Name:	IMG_20181011_203821.jpg Views:	481 Size:	35.4 KB ID:	17392  
weste46 is offline   Reply With Quote
Old 10-16-2018, 07:58 PM   #167
Estii
Senior Member
 
Estii's Avatar
 
Join Date: Nov 2014
Location: California
Posts: 215
iTrader: (0)
Default

Good god that pump was in there TIGHT!


Sent from my iPhone using Tapatalk
Estii is offline   Reply With Quote
Old 10-16-2018, 08:17 PM   #168
weste46
Junior Member
 
Join Date: Aug 2018
Location: Indiana
Posts: 21
iTrader: (0)
Default

Quote:
Originally Posted by Estii View Post
Good god that pump was in there TIGHT!


Sent from my iPhone using Tapatalk
I was afraid I would need to end up drilling the pump out like others on here have done! thankfully the shaft stayed seated inside the pump body.
weste46 is offline   Reply With Quote
Old 10-22-2018, 08:00 PM   #169
weste46
Junior Member
 
Join Date: Aug 2018
Location: Indiana
Posts: 21
iTrader: (0)
Default

For those interested,
I had to go back in to replaced my oil filter housing o-rings/bush/gasket.

When I removed all of the parts up to the oil filter housing, it seemed to me that I could reach the pipe underneath the intake manifold. This seems like it may be an easier way to approach this project, and you don't have to remove the intake manifold risking debris entering the combustion chamber.
Someone in an earlier post mentioned removing the battery and battery tray to reach the rear pipe. New coolant hoses may fish through okay, I'm not sure.

If done this way, you wouldn't have to remove the cluster of wires that rest on top of the lower intake manifold which are a pain to disconnect/reconnect blindly as you have to do, you could leave the fuel lines and injectors hooked up, and both manifolds could remain in their factory position. It took very little time to get to this state, whereas the "normal" way to get to this pipe has a lot of steps.
It would be more difficult to get your hand in to change the parts, but I think it's doable and overall would take less time. Getting my hands in to connect the starter wires and a few other connectors from the top electrical connector box was a total pain for me.
Attached Thumbnails
Click image for larger version Name:	IMG_20181021_143136.jpg Views:	505 Size:	69.3 KB ID:	17405  

Last edited by weste46; 10-22-2018 at 08:08 PM.
weste46 is offline   Reply With Quote
Old 10-23-2018, 07:34 AM   #170
paul somlo
Senior Member
 
Join Date: Sep 2006
Location: Greeley CO
Posts: 233
iTrader: (0)
Default

Quote:
Originally Posted by weste46 View Post
When I removed all of the parts up to the oil filter housing, it seemed to me that I could reach the pipe underneath the intake manifold.
Can you reach all three hose clamps?
paul somlo is offline   Reply With Quote
Old 10-23-2018, 01:40 PM   #171
weste46
Junior Member
 
Join Date: Aug 2018
Location: Indiana
Posts: 21
iTrader: (0)
Default

Quote:
Originally Posted by paul somlo View Post
Can you reach all three hose clamps?
I think so. If not, I think you could remove the pipe with the two 10mm bolts and pull it toward you to get more room for the rearmost hose, or remove the hose from whatever else it connects to and pull the pipe and hose out together.
weste46 is offline   Reply With Quote
Old 11-23-2018, 10:07 AM   #172
lokister
Junior Member
 
Join Date: Nov 2018
Location: San Francisco Bay Area
Posts: 13
iTrader: (0)
Default

Not a 318ti owner, but a 318i owner. I had the y-connector cause me some pain this week.

Long story short, I installed a defective thermostat. Which led to an overheat in the system and although I didn't blow my HG (mechanic said my compression levels were "on the money" but there could be a pinhole leak), the y-connector burst clean off.



I don't have the stomach to replace it myself so I forked over $300 in labor for my local mechanic to do it.

So, I can't endorse this PSA enough: REPLACE THESE PARTS!
lokister is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 07:41 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 80.41 k/95.29 k (15.62%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.