318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Suspension

Notices

Suspension Springs, sway bars, shocks.

.
» Recent Threads
96 M-Sport Slick-Top
08-05-2020 07:34 PM
Last post by runnr548
Yesterday 10:25 PM
6 Replies, 527 Views
parting out a nice 95...
05-16-2020 10:27 PM
Last post by Scott1283
Yesterday 09:58 PM
11 Replies, 4,030 Views
318ti Alaska Blue shell,...
Yesterday 08:11 PM
Last post by David325is
Yesterday 08:11 PM
0 Replies, 34 Views
wtb 4.45 lsd
08-08-2020 11:37 PM
Last post by joek84
08-08-2020 11:37 PM
0 Replies, 501 Views
Midnight Tuning...
02-08-2012 05:38 PM
Last post by E3X318is
08-08-2020 07:19 PM
195 Replies, 92,966 Views
Fuel pump keeps running...
08-06-2020 05:33 PM
Last post by Texas98ti
08-08-2020 06:25 PM
6 Replies, 455 Views
new engine build. dasc +...
01-02-2016 01:28 AM
Last post by andakn
08-08-2020 04:07 PM
209 Replies, 120,715 Views
318ti Is closing down??
07-31-2019 11:26 PM
Last post by BlackBMWs
08-08-2020 08:18 AM
51 Replies, 72,854 Views
Torque wrench...
07-28-2020 08:01 PM
Last post by J!m
08-08-2020 04:36 AM
5 Replies, 781 Views
318ti parts
06-09-2020 12:00 AM
Last post by dudecati
08-06-2020 08:58 PM
18 Replies, 4,150 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 03-08-2018, 04:39 PM   #1
manydubs
Senior Member
 
Join Date: Sep 2017
Location: KY
Posts: 109
iTrader: (0)
Default Improve the oversteer chararteristics

Are there any components that help to combat the oversteer and shift of the rear ends around corners?

It seems like my car (granted it has a heavier 6 cylinder engine) the rear end follows and sometimes leans over whilst following the front end in a turn, feeling somewhat unsafe.

Should I have to avoid something or snap quickly with a turn it feels like it could skid out easily.


I have all new suspension/steering components and a square wheel setup.

Would a stiffer front spring help or stiffer rear shocks?



I have lowered the pressure in my front tires to 35 and left the rear at 40psi.

Thanks
manydubs is offline   Reply With Quote
Old 03-08-2018, 05:43 PM   #2
macilona
Senior Member
 
Join Date: Aug 2008
Location: San antonio, tx
Posts: 131
Vehicles
iTrader: (0)
Default

Visit strong-strut.com and look at the rear brace for the z3 and e30, which have the same rear suspension as the ti. This is a brace that fits under the car and tightens the suspension....easy bolt on installation. I got it when other track drivers told me that my rear suspension looked loose through tight corners...makes a noticable difference.
macilona is offline   Reply With Quote
Old 03-08-2018, 05:53 PM   #3
manydubs
Senior Member
 
Join Date: Sep 2017
Location: KY
Posts: 109
iTrader: (0)
Default

Interesting.
manydubs is offline   Reply With Quote
Old 03-09-2018, 01:18 PM   #4
manydubs
Senior Member
 
Join Date: Sep 2017
Location: KY
Posts: 109
iTrader: (0)
Default

Very expensive.
manydubs is offline   Reply With Quote
Old 03-18-2018, 11:55 AM   #5
sirius815
Member
 
Join Date: Dec 2017
Location: NoVA
Posts: 49
iTrader: (0)
Default

You'd want more pressure in the front than the rear more than likely, but definitely go with a wider tire in the back. With some fender rolling you can easily fit a 265 andaybe even a 275. Also make sure camber and toe are within spec - weld in adjustment plates if needed.

Sent from my Nexus 6 using Tapatalk
sirius815 is offline   Reply With Quote
Old 03-18-2018, 12:43 PM   #6
manydubs
Senior Member
 
Join Date: Sep 2017
Location: KY
Posts: 109
iTrader: (0)
Default

Found out that mine has camber and toe plates welded on. Driver side missing ECS rric bolts, going to install them this week and set it up better.
manydubs is offline   Reply With Quote
Old 03-23-2018, 04:41 PM   #7
manydubs
Senior Member
 
Join Date: Sep 2017
Location: KY
Posts: 109
iTrader: (0)
Default

Ended up installing Eccentric Bolts in the rear drivers side to adjust the toe and Camber which were both way off.

Luckily someone else had installed the adjustment plates prior but did not put eccentric bolts in place, just standard bolts.

This and replacing my failing rear bushing made a substantial difference.

Car already had upgraded subframe bushings.
manydubs is offline   Reply With Quote
Old 03-23-2018, 08:18 PM   #8
sirius815
Member
 
Join Date: Dec 2017
Location: NoVA
Posts: 49
iTrader: (0)
Default

Sweet! I have no idea why someone would put non-eccentric bolts into elongated holes - what a bad move!
sirius815 is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Improve performance - low budget CarCraze Engine 36 10-21-2008 08:37 PM


All times are GMT +1. The time now is 07:28 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2020, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 85.32 k/101.50 k (15.94%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.