318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Electrical


Electrical All wiring questions.

» Recent Threads
98 318ti swap?
Yesterday 03:57 PM
Last post by ZEK
Today 12:39 AM
1 Replies, 169 Views
M44 engine, 5 spd trans,...
Yesterday 07:28 PM
Last post by pilsberry
Yesterday 07:28 PM
0 Replies, 162 Views
Feeler: 98 318Ti Black M...
09-09-2017 03:57 AM
Last post by GregGT
Yesterday 04:38 PM
33 Replies, 11,808 Views
Euro glass headlights
09-24-2014 10:27 PM
Last post by tigruppe
07-20-2018 09:01 PM
202 Replies, 115,126 Views
Lurker from St Louis
07-20-2018 01:51 PM
Last post by Ol Red Duc
07-20-2018 01:51 PM
0 Replies, 168 Views
rare EURO interior...
05-02-2016 11:09 PM
Last post by runnr548
07-20-2018 03:26 AM
53 Replies, 19,544 Views
Autobahn Country Club...
07-20-2018 02:23 AM
Last post by Feffman
07-20-2018 02:23 AM
0 Replies, 168 Views
1996 318Ti/M3 swapped...
07-14-2018 07:17 PM
Last post by 30yrMbr
07-19-2018 11:15 AM
2 Replies, 816 Views
Air Pump Simulator DIY...
11-18-2008 01:37 PM
Last post by spidertri
07-18-2018 06:15 PM
114 Replies, 71,702 Views
for sale grey door cards...
04-17-2018 02:29 PM
Last post by derek502
07-17-2018 03:16 PM
3 Replies, 1,527 Views
Reply Share/Bookmark
Thread Tools Display Modes
Old 08-27-2008, 04:07 PM   #31
Join Date: Oct 2007
Location: Devon U.K.
Posts: 34
iTrader: (0)

90% of the time the problem is the connector under the seat, it either gets kicked or the contact areas need a clean.You can reposition the cable if you have a good look at it, just note how far the seat moves from end to end. The dealers must be making a fortune from this poor design.
Good job the rest of the car is far better!!!!
greenmeanie is offline   Reply With Quote
Old 09-05-2009, 12:57 AM   #32
Senior Member
Join Date: Aug 2007
Location: louisiana
Posts: 188
iTrader: (0)

just take out the cluster and pull the srs bulb out if it keeps you from getting an inspection sticker. you take off the headlight switch cover and fog log cover and unscrew the four torx head screws holding in it then just wiggle out the cluster and take the bulb out.
318tian is offline   Reply With Quote
Old 09-05-2009, 01:20 AM   #33
Senior Member
Join Date: Sep 2007
Location: asdfasdf
Posts: 10,029
iTrader: (8)

it would be nice if it was that simple, unless it's some crappy place where everyone half-asses everything they'll figure it out
tiFreak is offline   Reply With Quote
Old 11-11-2009, 05:50 PM   #34
Senior Member
L84THSKY's Avatar
Join Date: Sep 2004
Location: Manassas, VA
Posts: 4,129
iTrader: (0)
Default If I may piggy back on this thread

Went to Brooklyn Monday night to see a concert. On the way back, I hit a bump/pothole that really slammed my car. The SRS light came on, and stayed on. I have the Peake reset tool and reset it, but it came right back.

What could have happened to mess up the SRS system? I will try to reset again, and remove and reinstall the fuse.

1998 (July) 318ti, 5-spd
OEM Armrest • Blaupunkt Heidelberg CD50 CD Player/Compact Drive MP3 Player • Diamond Audio 5.25" rear speakers • Navman ICN 530 GPS • BMWALARM.COM (with comfort settings) after market alarm system • Magnecor 8.5mm wires • M-Z3 Shifter/Momo Knob • Burlwood Dashboard • Stromung Exhaust • X-brace • Racing Dynamics Front Strut Bar • Carbonio C.A.I. • 17" Rial Rims • Vader Seats/Heated/Lumbar Support • M-tech Steering Wheel/Front Sway Bar/Front & Rear Bumper • Depos/w 6500K Angel Eyes/6000K HIDs • Clear Corners • M3 Mirrors • UUC Light Weight Flywheel/M5 Clutch/M3 Clutch Slave • E28 3.46 LSD/Mcoupe Cover/E30 Flanges & Halfshafts • UUC S.S. Brake/Clutch Lines • Hartge Roof Spoiler • BavAuto Springs• Bilstein Sport Struts/Shocks • E46 M3 Rear Shock Mounts • SPC Front Camber Kit • Reiger Hatch Spoiler • BavAuto Rear Camber Kit • Dinan Stage II Software • Turner Rear Sway Bar Reinforcements • BMW E46 Auto dimming mirror with Clown Nose alarm • Engine Compartment Light • Heated Wiper Fluid Retrofit • OEM Fire Extinguisher • Da'lan Trailer Hitch • Rear Sun Shade • OEM Fog Light Retrofit • H & R MZ3 Rear Sway Bar/ UUC Adjustable End Links • Cruise Control Retrofit • On Board Computer Retrofit • M3 twistie style side skirts • Carbon Fiber Hood
L84THSKY is offline   Reply With Quote
Old 11-12-2009, 11:06 PM   #35
Senior Member
Join Date: Sep 2007
Location: asdfasdf
Posts: 10,029
iTrader: (8)

maybe you disconnected or severed the wire on one of the crash sensors? I'm not sure exactly where they are but it's near the front bumper
tiFreak is offline   Reply With Quote
Old 11-09-2013, 02:49 PM   #36
Junior Member
Join Date: Nov 2013
Location: lovingston, va
Posts: 4
iTrader: (0)

airbag light stays on; 1997 Z3; i have the reset tool . i have a 100 ohm resistor, but my black connector has four wires instead of three. any ideas which to put the resistor in??
trusty110 is offline   Reply With Quote
Old 03-17-2015, 12:07 PM   #37
John Firestone
Senior Member
John Firestone's Avatar
Join Date: Nov 2004
Location: Bremerhaven, Germany
Posts: 961
iTrader: (0)

Originally Posted by trusty110 View Post
airbag light stays on; 1997 Z3.... i have a 100 ohm resistor, but my black connector has four wires instead of three. any ideas which to put the resistor in??
If it were my car, I might get a gold Siemens contact and apply the resistor at the SRS controller connector: fewer things to fail.

What fault(s) are setting the airbag light?

Last edited by John Firestone; 03-17-2015 at 12:15 PM.
John Firestone is offline   Reply With Quote


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT +1. The time now is 11:28 AM.

Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2018, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 85.43 k/101.12 k (15.51%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.