318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Maintenance

Notices

Maintenance Service Interval questions, oil change info.

.
» Recent Threads
What intake for S54...
Today 09:29 AM
Last post by Simas323
Today 09:29 AM
0 Replies, 5 Views
Happy Birthday barische
Today 06:00 AM
Last post by 1996 328ti
Today 06:00 AM
0 Replies, 32 Views
Window coming off track
01-27-2003 04:51 PM
Last post by sortasorted
Today 05:53 AM
215 Replies, 79,996 Views
Injector...
Yesterday 11:23 PM
Last post by KASZ
Today 01:34 AM
2 Replies, 94 Views
OEM roof spoiler
06-14-2018 01:19 AM
Last post by sortasorted
Yesterday 06:27 PM
16 Replies, 4,076 Views
Swap Manual Q&A
01-09-2007 04:32 AM
Last post by Dphu
02-16-2019 05:21 PM
195 Replies, 55,447 Views
new engine build. dasc +...
01-02-2016 02:28 AM
Last post by Jean H.318TI
02-16-2019 05:55 AM
190 Replies, 94,606 Views
throttle bodies on the...
01-19-2019 12:20 AM
Last post by jerseytim
02-15-2019 11:13 PM
2 Replies, 576 Views
Racewars Australia -...
02-15-2019 09:09 PM
Last post by 318tiFatherFigure
02-15-2019 09:09 PM
0 Replies, 149 Views
Magnaflow catback $60
02-08-2019 07:18 PM
Last post by Mongwit
02-14-2019 06:41 AM
2 Replies, 590 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 11-17-2018, 04:56 AM   #1
S.W.B.C
Junior Member
 
Join Date: Dec 2009
Location: Oregon
Posts: 17
iTrader: (0)
Default SIR crankshaft tool

Grasping at straws but anyone in the Portland area that has the SIR tool for securing harmonic balancer for removing the crankshaft bolt? Rent , barter, or trade for beer or???
Thanks so much!!!!!
Silas
S.W.B.C is offline   Reply With Quote
Old 11-24-2018, 04:20 AM   #2
paul somlo
Senior Member
 
Join Date: Sep 2006
Location: Greeley CO
Posts: 196
iTrader: (0)
Default

I use a pin to lock the flywheel - the tip is 0.307 diameter and 0.392 in length, the next section is 0.452 in diameter and 1.577 inches in length. The next larger section doesn't matter.

You might get away using a 5/16" drill bit or an 8mm bolt.

I was concerned that I'd be stressing the crankshaft, but I've used it several times now with no ill effects, and I've read accounts of others doing likewise.
Attached Thumbnails
Click image for larger version Name:	PB232533.JPG Views:	18 Size:	84.9 KB ID:	17417  
paul somlo is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
crankshaft pulley holding tool rbush Engine 16 02-28-2016 09:36 PM
Misc parts FS: M44 Crank Locking Pin/Dowel Tool for Head repair 96silver318ti Parting out & Parts (US) 4 08-22-2013 11:58 PM
DIY: R&R crankshaft position sensor elfhearse Knowledge Base 4 05-12-2010 04:24 AM
MemoScan B200 SRS/Airbag Tool CirrusSR22 Maintenance 6 05-30-2009 08:21 PM
Source for rear subframe bushing tool. bullmand Suspension 7 12-13-2007 05:07 PM


All times are GMT +1. The time now is 10:02 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2019, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 67.31 k/77.76 k (13.43%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.