» Site Navigation | | » Recent Threads | looove 04-16-2024 01:18 PM 04-16-2024 01:18 PM 0 Replies, 408 Views | | lolita porn 04-13-2024 11:45 PM 04-13-2024 11:45 PM 0 Replies, 213 Views | lolita porn 04-13-2024 11:43 PM 04-13-2024 11:44 PM 1 Replies, 139 Views | lolita porn 04-13-2024 11:40 PM 04-13-2024 11:41 PM 1 Replies, 138 Views | lolita porn 04-13-2024 11:38 PM 04-13-2024 11:39 PM 1 Replies, 143 Views | lolita porn 04-13-2024 11:36 PM 04-13-2024 11:37 PM 1 Replies, 137 Views | lolita porn 04-13-2024 11:35 PM 04-13-2024 11:35 PM 0 Replies, 120 Views | lolita porn 04-13-2024 11:34 PM 04-13-2024 11:34 PM 0 Replies, 126 Views | lolita porn 04-13-2024 11:33 PM 04-13-2024 11:33 PM 0 Replies, 118 Views | | | | | 05-23-2015, 10:27 PM | #1 | Member Join Date: May 2008 Location: Central Illinois Posts: 59 | CV-Axle Half Shaft from Advanced Auto Parts... Advanced Auto Parts has GSP Brand CV Axle Assembly (P/N: NCV27994). They have a 90 Day Warranty (at the discretion of AAP). I ordered two for $169.98 including free shipping. Note: the outboard CV body is slightly larger diameter than the OEM unit but there's enough clearance and the ABS Sensor is not affected. Do not order the "NCV27995" unit as several reviews say they're too long for 318ti. GSP Brand CV Axle Assembly (P/N: NCV27994): Compressed Length: 23 1/8” OBJ Spline Count: 27 IBJ Spline Count: N/A IBJ Type: Bolt On ABS Count: 48 ABS Style: Window Weight: 14.48 Lbs. 23MAY2015 - @171,368 Miles I replaced the old CV Axle Assemblies with new GSP Brand CV Axle Assemblies. They supplied a new Locking type Axle Nut and plain flat Washer but both were not correct. The Nut was larger than the OEM 30mm one and the plain flat Washer obviously wouldn’t lock the old Nut. Secondly, they supplied new Inboard-CV Joint Bolts but they were of the wrong thread pitch and only 5 supplied versus 6 needed. I put Permatex Anti-Seize Compound on the Shaft Splines before inserting them into the Wheel Hubs. The Cover Caps on the Inboard-Joints were not correctly aligned nor fully seated. I hammered a steel Punch through the Bolt Holes to straighten them before installing the Axles. Only did a short test drive so far but seem fine... | | | 05-25-2015, 01:12 AM | #2 | Senior Member Join Date: Jul 2007 Location: norcal - 94590 Posts: 3,186 | Keep us posted on their longevity... I have not had good luck with replacement half shafts, had one self destruct after just a few months (not that brand, but I suspect they are all remanufactured at a central factory and then resold by wholesalers). __________________ James 95 active w/leather interior and sport interior conversion, Vaders, full M-Tech exterior conversion. Now m50 swapped* Eibach sway bars, D2 Coilovers, Depo's w/AE's, blacked-out sides and grills, LeatherZ console and door armrests, 1 series starter button mod, and custom finished Style 5's <--- in this color! Named "Roddy": *M50 6 cyl. swap with fan delete, S50 cams and chip, AFE stage 2 intake, M3 clutch and 11.5 lb Fidanza flywheel, 3.15LSD, battery relocated to rear and complete custom exhaust. Sweet! 97 318ti sport, Alaska Blue, Contours, coilovers, Dove Vaders and custom black/grey interior named "Max" 95 318ti Active in Cosmos, S50 swap in progress... named "Pit" SUPPORT 318ti.org! CLICK THE LINK ABOVE! Hosting a forum like this is not free. 318ti.org is one of the best BMW forums on the web because it is member supported, not vendor supported. The cost to become a Supporter is a nominal $10.00... A YEAR! DO IT! NOW! | | | 11-15-2016, 10:27 PM | #3 | Junior Member Join Date: Nov 2016 Location: Florida Posts: 3 | How are they doing ?? | | | 11-16-2016, 12:10 AM | #4 | Member Join Date: May 2008 Location: Central Illinois Posts: 59 | Quote: Originally Posted by E36compactdrift1995 How are they doing ?? | Can't sat for sure since I sold the car last Spring. The new axles were working great and they had 7,282 miles on them. The quality was good so I'd say go for it. | | | 11-16-2016, 12:11 AM | #5 | Junior Member Join Date: Nov 2016 Location: Florida Posts: 3 | Ok thanks man ! | | | 11-16-2016, 12:14 AM | #6 | Junior Member Join Date: Nov 2016 Location: Florida Posts: 3 | Btw with them being long how did you manage to get them in jw now that I think about it . Just worried I've been threw 3 sets off axles that didn't fit .. | | | 11-16-2016, 05:01 AM | #7 | Member Join Date: May 2008 Location: Central Illinois Posts: 59 | NCV27994 is the correct length. Do not get the NCV27995 as they're too long. | | | | Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | | Posting Rules | You may not post new threads You may not post replies You may not post attachments You may not edit your posts HTML code is Off | | | |