318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Transmission

Notices

Transmission Automatic, manual and shift lever discussions.

.
» Recent Threads
1996 332ti supercharged...
06-08-2019 08:27 PM
Last post by slowoldpoop
Today 07:59 PM
6 Replies, 1,542 Views
Mostly new to cars and a...
07-11-2019 09:28 PM
Last post by paul somlo
Today 02:33 AM
4 Replies, 461 Views
318to supercharger kit
Yesterday 09:39 PM
Last post by jacksondnm02
Yesterday 09:39 PM
0 Replies, 171 Views
Seeking 318ti with...
06-30-2019 07:36 PM
Last post by Trusted-1
07-14-2019 07:26 PM
7 Replies, 1,332 Views
TWO! 1996 California Top...
07-14-2019 07:25 PM
Last post by Trusted-1
07-14-2019 07:25 PM
0 Replies, 232 Views
The 318ti OBD-II engine...
10-19-2006 06:48 PM
Last post by J!m
07-12-2019 10:03 PM
147 Replies, 90,566 Views
Rudolph the Red 318ti
05-06-2019 10:49 PM
Last post by MisterM52
07-12-2019 07:32 PM
27 Replies, 4,913 Views
Euro Headlights (New)
12-31-2018 05:06 PM
Last post by sprnova
07-12-2019 02:58 PM
7 Replies, 2,535 Views
M44 Supercharged Project...
04-07-2019 06:54 AM
Last post by joe1602
07-12-2019 01:33 PM
8 Replies, 1,581 Views
2000 z3 m52 into a 99 ti?
07-09-2019 03:04 AM
Last post by joe1602
07-12-2019 12:23 PM
12 Replies, 844 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 04-22-2016, 09:05 AM   #1
Bwwaaaa
Member
 
Bwwaaaa's Avatar
 
Join Date: Aug 2015
Location: Arizona
Posts: 99
iTrader: (0)
Default ZF Swap with M44

So before the inevitable "Why would you do that?" it really boils down to a timing thing. The car will be getting an S52 later this year, but I'm not really quite there yet.

I'm in need of a new driveshaft, but the opportunity came up to buy a ZF transmission, with the driveshaft and everything needed to drop it into a ti. The car it is coming out of has an M52 I believe, but I need to use this setup with the M44 until I'm ready to swap later this year. I was wondering if there was anything I need to keep in mind to make this swap work, or should it all just bolt up and work as is? My understanding is I'll be getting the transmission, shift linkage, clutch, brace and driveshaft. But I don't know if there are any other specific parts I should buy for this swap to work with the M44.

While I could just get another stock driveshaft, I feel like it's a waste given I'll be swapping later this year. So if I can make the ZF transmission and driveshaft work for a few months (mainly to last a trip out to California) I'd much prefer to go that route.

Thanks!
__________________

@speedlimitless
1998 318ti Build
Bwwaaaa is offline   Reply With Quote
Old 04-22-2016, 07:51 PM   #2
Bwwaaaa
Member
 
Bwwaaaa's Avatar
 
Join Date: Aug 2015
Location: Arizona
Posts: 99
iTrader: (0)
Default

So I got the replies I was looking for in a Facebook group. I figured I'd post the responses I got here, in case someone else is looking up this information in the future.

Quote:
If I remember right it'll bolt right up, only thing is with the master cylinder designed for the Getreg you'll have a stiffer pedal with the ZF. Other than that if you get all that stuff you should be good.
Quote:
Yes, it works. The slave needs to match the pressure plate. The flywheels and clutch kit should be matched for the transmission. Starter should work as is.
Quote:
The hydraulics will work, just may be stiffer pedal depending on the pressure plate you use. I ran my s52 swap for a long time with the stock master and slave, was just kinds stiff because the pressure plate is stiff. But with a 325i clutch it should work better
Quote:
All non-m masters and slaves are the same. The 92 had a different master. The s50/2 slave is different in piston bore. Stock will be fine. If you use an s50/2 clutch with non-m slave it will be very heavy at the clutch pedal and initiates right off the floor. It's all bolt in but you need the linkage from the zf for the guibo and shifter location.
Thanks to the guys in the 318ti Facebook discussion group. Looks like if you go to do this swap yourself, it should work, just be a great deal heavier on the clutch.
__________________

@speedlimitless
1998 318ti Build
Bwwaaaa is offline   Reply With Quote
Reply

Bookmarks

Tags
m44 , swap , transmission


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
318ti use Z3 DME for SAP delete and emissions delete new318tifan Engine 5 02-03-2016 03:24 PM
M44 swap into 328? toveycom Engine Swaps 0 11-30-2013 10:38 PM
m42 to m44 swap issues b33m3r88 Engine Swaps 7 02-12-2011 02:18 AM
M44 Blew....Time For M52 swap EuroSpec89 Engine Swaps 12 09-28-2010 03:38 AM
M42 to m44 Obd2 Swap Questions allenergies Engine Swaps 1 03-09-2009 05:31 PM


All times are GMT +1. The time now is 11:55 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2019, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 73.11 k/83.80 k (12.76%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.