318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Engine Swaps

Notices

Engine Swaps Engine conversions.

.
» Recent Threads
1999 M-Sport For Sale
12-31-2023 05:10 PM
Last post by Coop540iT
03-23-2024 06:39 PM
1 Replies, 100,124 Views
Once again 318ti owner...
03-20-2024 12:39 PM
Last post by two30grain
03-22-2024 02:04 PM
1 Replies, 63,036 Views
What brakes do I...
03-20-2024 03:27 PM
Last post by huirtera
03-20-2024 03:27 PM
0 Replies, 60,270 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 10-05-2006, 03:25 AM   #1
pnosker
Senior Member
 
Join Date: Aug 2006
Location: Central NJ
Posts: 2,440
iTrader: (4)
Default E30 318i M40 to M44 conversion

Hey guys,

A friend of mine's timing chain broke in her E30 318i and I was thinking about recommending an M44 to replace the M42 that came with her car. The M42 is plagued with issues involving the timing chain breaking. How hard would it be to replace the M42 + transmission with the M44 + transmission provided I have the wiring harnesses, DME, and EWS together?

As far as I understand, the motors almost fit together perfectly, but I'm sketchy on these motors. The transmission could be dismounted and connected to the current tranny, if needed too.
pnosker is offline   Reply With Quote
Old 10-08-2006, 08:43 AM   #2
windnsea00
Senior Member
 
Join Date: Feb 2005
Location: la jolla, ca
Posts: 222
iTrader: (0)
Default

I would not go thru the trouble of doing an OBDII to OBDI swap for a 4 cylinder. There are TONS of little modifications you have to make. If you must have DOHC go for the M42.
windnsea00 is offline   Reply With Quote
Old 10-08-2006, 02:21 PM   #3
pnosker
Senior Member
 
Join Date: Aug 2006
Location: Central NJ
Posts: 2,440
iTrader: (4)
Default

Why would I have to do an OBDII to OBDI conversion? I thought that OBD was only required for Inspections and they would inspect it without OBD at all since it's made pre-OBDII.
pnosker is offline   Reply With Quote
Old 10-08-2006, 08:53 PM   #4
bullmand
Senior Member
 
bullmand's Avatar
 
Join Date: Jun 2003
Location: Halethorpe, MD
Posts: 1,028
iTrader: (0)
Default

I suspect it would work fairly well. The most difficult thing to get working would be the EWS. Did the E30s have this? Isn't there hardware in the steering column that's part of this system? That's the only thing I would worry about. If you have the whole M44 with all the associated sensors, etc. I think you'll be good. Don't forget the airbox and all the sensors there too. The DME will want those. You might also have difficulties with the ASC+T. I don't know if the E30 have the wheel-slip sensors. Good luck and keep us posted.
__________________
'98 Alaska Blue Sport
www.baltimorecitypipeband.com
bullmand is offline   Reply With Quote
Old 10-09-2006, 05:18 AM   #5
john318isau
Member
 
Join Date: Aug 2006
Location: NSW, Australia
Posts: 63
iTrader: (0)
Default

Are you sure it's an M40 engine? I didn't think that the M40 was available in the USA and it has a timing belt not a chain. USA 318i models had the M42 engine which is a twin cam 1.8L with a timing chain.

Converting from M40 to M42 in an E30 would be much easier than an M44.
john318isau is offline   Reply With Quote
Old 10-09-2006, 11:43 AM   #6
pnosker
Senior Member
 
Join Date: Aug 2006
Location: Central NJ
Posts: 2,440
iTrader: (4)
Default

I'm pretty sure, but not positive. It's whichever motor had the premature timing chain failure in 1991. Actually, it sounds like the M42 makes more sense now.
pnosker is offline   Reply With Quote
Old 10-09-2006, 11:52 AM   #7
john318isau
Member
 
Join Date: Aug 2006
Location: NSW, Australia
Posts: 63
iTrader: (0)
Default

Well if it is a USA car then it won't be an M40 for sure so it must be an M42 and, as I said earlier, the M40 has a belt not a chain. M42's had a common problem with the profile gasket but I am not aware of premature timing chain failure as a common problem. (The two E30 318is's I have owned both have had 150,000+ miles on their original chains). However, the timing chain tensioner was changed in design and the part from the M44 is now the recommended replacement for the M42.

The M44 and M42 are very similar in specification except the M44 is 100cc larger. Power is almost the same and torque is up slightly but the peak occurs lower in the rev range. I would say that it wouldn't be worth the expense to install an M44 in an E30 due to large number of changes necessary. Fitting a second hand M42 would be the easiest and most cost effective option.
john318isau is offline   Reply With Quote
Old 10-11-2006, 10:58 PM   #8
pnosker
Senior Member
 
Join Date: Aug 2006
Location: Central NJ
Posts: 2,440
iTrader: (4)
Default

Alright, thanks for your advice guys. I've told her not to get the M44 because of these issues. Looks like she's gonna get a 318ti now! Maybe we'll have another forum member soon.
pnosker is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 11:05 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 79.69 k/94.59 k (15.76%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.