318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Suspension

Notices

Suspension Springs, sway bars, shocks.

.
» Recent Threads
Oil Filter Housing Leak...
02-14-2008 09:21 PM
Last post by paul somlo
Today 12:59 AM
114 Replies, 80,599 Views
Is this a clubsport?
Yesterday 06:54 AM
Last post by dranthony
Today 12:19 AM
3 Replies, 152 Views
California Top Trim...
07-16-2014 08:59 AM
Last post by 3DGE
Yesterday 09:37 PM
9 Replies, 4,421 Views
M42 / M44 loose...
12-07-2018 08:10 PM
Last post by Frach23
12-07-2018 09:34 PM
1 Replies, 305 Views
Anyone seen a carbon...
11-16-2018 06:19 AM
Last post by eurohb
12-07-2018 05:26 AM
1 Replies, 436 Views
New here so lets arc you...
11-09-2018 08:56 AM
Last post by acidjzaz
12-07-2018 12:34 AM
1 Replies, 470 Views
FS: E36 Brakes, rotors,...
12-06-2018 06:30 AM
Last post by FunElan
12-06-2018 09:29 PM
3 Replies, 240 Views
WTB **** 5 Speed BMW...
12-03-2018 02:01 AM
Last post by kaiburger
12-06-2018 08:06 PM
2 Replies, 360 Views
1995 318ti Clusport S52...
10-30-2018 04:31 PM
Last post by Tom318ti
12-06-2018 04:59 PM
5 Replies, 1,115 Views
1998 BMW 318TI M Sport...
11-29-2018 04:58 PM
Last post by BMWannabe
12-05-2018 10:43 PM
19 Replies, 1,283 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 03-08-2018, 05:39 PM   #1
manydubs
Senior Member
 
Join Date: Sep 2017
Location: KY
Posts: 109
iTrader: (0)
Default Improve the oversteer chararteristics

Are there any components that help to combat the oversteer and shift of the rear ends around corners?

It seems like my car (granted it has a heavier 6 cylinder engine) the rear end follows and sometimes leans over whilst following the front end in a turn, feeling somewhat unsafe.

Should I have to avoid something or snap quickly with a turn it feels like it could skid out easily.


I have all new suspension/steering components and a square wheel setup.

Would a stiffer front spring help or stiffer rear shocks?



I have lowered the pressure in my front tires to 35 and left the rear at 40psi.

Thanks
manydubs is offline   Reply With Quote
Old 03-08-2018, 06:43 PM   #2
macilona
Senior Member
 
Join Date: Aug 2008
Location: San antonio, tx
Posts: 121
Vehicles
iTrader: (0)
Default

Visit strong-strut.com and look at the rear brace for the z3 and e30, which have the same rear suspension as the ti. This is a brace that fits under the car and tightens the suspension....easy bolt on installation. I got it when other track drivers told me that my rear suspension looked loose through tight corners...makes a noticable difference.
macilona is offline   Reply With Quote
Old 03-08-2018, 06:53 PM   #3
manydubs
Senior Member
 
Join Date: Sep 2017
Location: KY
Posts: 109
iTrader: (0)
Default

Interesting.
manydubs is offline   Reply With Quote
Old 03-09-2018, 02:18 PM   #4
manydubs
Senior Member
 
Join Date: Sep 2017
Location: KY
Posts: 109
iTrader: (0)
Default

Very expensive.
manydubs is offline   Reply With Quote
Old 03-18-2018, 12:55 PM   #5
sirius815
Member
 
Join Date: Dec 2017
Location: NoVA
Posts: 47
iTrader: (0)
Default

You'd want more pressure in the front than the rear more than likely, but definitely go with a wider tire in the back. With some fender rolling you can easily fit a 265 andaybe even a 275. Also make sure camber and toe are within spec - weld in adjustment plates if needed.

Sent from my Nexus 6 using Tapatalk
sirius815 is offline   Reply With Quote
Old 03-18-2018, 01:43 PM   #6
manydubs
Senior Member
 
Join Date: Sep 2017
Location: KY
Posts: 109
iTrader: (0)
Default

Found out that mine has camber and toe plates welded on. Driver side missing ECS rric bolts, going to install them this week and set it up better.
manydubs is offline   Reply With Quote
Old 03-23-2018, 05:41 PM   #7
manydubs
Senior Member
 
Join Date: Sep 2017
Location: KY
Posts: 109
iTrader: (0)
Default

Ended up installing Eccentric Bolts in the rear drivers side to adjust the toe and Camber which were both way off.

Luckily someone else had installed the adjustment plates prior but did not put eccentric bolts in place, just standard bolts.

This and replacing my failing rear bushing made a substantial difference.

Car already had upgraded subframe bushings.
manydubs is offline   Reply With Quote
Old 03-23-2018, 09:18 PM   #8
sirius815
Member
 
Join Date: Dec 2017
Location: NoVA
Posts: 47
iTrader: (0)
Default

Sweet! I have no idea why someone would put non-eccentric bolts into elongated holes - what a bad move!
sirius815 is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Improve performance - low budget CarCraze Engine 36 10-21-2008 09:37 PM


All times are GMT +1. The time now is 03:25 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2018, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 85.77 k/101.93 k (15.85%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.