318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Engine

Notices

Engine Tuneups, chips, wires, spark plugs.

.
» Recent Threads
Rebuild M44 or S52 swap?
12-13-2019 07:21 AM
Last post by ZEK
12-13-2019 10:32 PM
1 Replies, 380 Views
FS: 1998 BMW 318ti...
11-25-2019 12:57 AM
Last post by doucy2
12-13-2019 07:29 PM
5 Replies, 867 Views
Ultimate Supercharger...
06-23-2019 09:06 AM
Last post by Blindsparky
12-11-2019 04:38 AM
101 Replies, 63,772 Views
bc racing or KWs?
12-05-2019 02:48 AM
Last post by Z3nki
12-09-2019 05:41 AM
3 Replies, 634 Views
heater bowden cable fix...
02-25-2012 02:50 AM
Last post by Hotredti
12-09-2019 01:00 AM
16 Replies, 15,445 Views
FS: 17" Style 40 / FULLY...
12-05-2019 09:34 PM
Last post by Meller1
12-05-2019 09:34 PM
0 Replies, 360 Views
FS: Brake UPGRADE Thread...
12-05-2019 09:33 PM
Last post by Meller1
12-05-2019 09:33 PM
0 Replies, 225 Views
FS: E36 M3 OEM Mirrors
11-13-2019 05:39 PM
Last post by Meller1
12-05-2019 09:26 PM
1 Replies, 737 Views
DASC Inforation or parts
12-05-2019 01:15 PM
Last post by pvansickler
12-05-2019 07:38 PM
2 Replies, 300 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 07-22-2019, 11:43 PM   #16
thenjnick
Junior Member
 
Join Date: Aug 2018
Location: Beachwood
Posts: 28
iTrader: (0)
Default

Got it, thanks. Im not sure about the timing marks on these. Do you use the timing block tool? i dont remember if the m5x tool was compatible with the m4x one. Thats a shame you took it all off when you didnt have to but at least now you can see exactly how much that chain is smacking around in there..yikes. Ill have to do mine sooner or later, its a pain to find any downtime for this car since it is my daily currently. I can see some rtv squeezed out the top corner of the case as if someone’s been in there already, or maybe this is factory beats me..ill have a look at the timing marks if you dont beat me to it


Sent from my iPhone using Tapatalk
thenjnick is offline   Reply With Quote
Old 07-23-2019, 12:54 AM   #17
MisterM52
Member
 
MisterM52's Avatar
 
Join Date: Jul 2017
Location: Stuttgart, Germany
Posts: 98
iTrader: (0)
Default

I think this would be a nice video on timing, real simple, the same tool for the M52/M5 should work if its this one he is using.

https://www.youtube.com/watch?v=ksP5tSrz_s4
MisterM52 is offline   Reply With Quote
Old 07-23-2019, 02:01 AM   #18
thenjnick
Junior Member
 
Join Date: Aug 2018
Location: Beachwood
Posts: 28
iTrader: (0)
Default

Thats a good one, at least one of about 3 ive ever seen on the internet. Not much video content on these engines.


Sent from my iPhone using Tapatalk
thenjnick is offline   Reply With Quote
Old 10-06-2019, 09:57 AM   #19
MisterM52
Member
 
MisterM52's Avatar
 
Join Date: Jul 2017
Location: Stuttgart, Germany
Posts: 98
iTrader: (0)
Default

So I think the issue I was having months ago with my little Ti finally came to light. I bought the car as a daily and after a few months the issues began after a speed bump and I have read how the ABS not working can cause the engine to misfire.

Anyway so today it was driving fine, no usual hesitation or misfires but I finally saw the ABS light came on (no issue with braking)

Here is what I get in INPA

ASCMK20

129 main relay inside control unit - How do I get to the bottom of this? Is it a relay inside the ABS Unit or the relay in the fues box or is there one inside the ECU compartment?

121 height adaption (Error Load registration) - Unsure what this is for but I assume its related to the two.

175 Output suction pipe-switching - This I understand is DISA Related?

I cant seem to nail down if its the front two sensors or the ABS unit the culprit or some relay.

Any input appreciated.
MisterM52 is offline   Reply With Quote
Old 10-08-2019, 10:46 AM   #20
MisterM52
Member
 
MisterM52's Avatar
 
Join Date: Jul 2017
Location: Stuttgart, Germany
Posts: 98
iTrader: (0)
Default FIXED!

Hi everyone, I have some fantastic news. All my issues have been fixed and the root was ASC & ABS. I did the ABS repair, and just went for a drive, no more misfires, no more hesitations! no more issues, didn't even need to disable the ASC. All is working great!

So I went after the ABS module today, took the electronic controller part off, cut the plastic housing open using a angle grinder (can use a dremel rotary tool) I found the dry solder joints. I re soldered it all then put the lid back on and plastic welded it (you can use the soldering iron plus some left over abs plastic to do such repairs) then cleaned it off with the grinder a bit and sealed it with some plastic epoxy just for good measure.


I also found a fuse (IIRC fuse 21 5A/32V I believe?) that was blown. Thanks to that fuse blowing I was able to narrow it more down to the ABS/ASC as I believe the solder joints after the speed bump were so lose that it was intermittent when the engine was pulling hard the ABS must had enough of a kickback/jerk to loosen the solder joints inside, then same applied going uphill and shorting that eventually lead blowing the fuse months later, which thankfully disabled the ASC and the car was able to just drive fine.

But now all is running fine, the ABS & ASC works fine and the lights have gone. The down side was when putting it all back together one of the ABS lines are now cross threaded which I will have to repair! Haha! I could had done the repair without taking the abs lines off (a little bending will be required). Something I will attempt to solve tomorrow or this week when time allows but for now I am so happy that my little Red Ti is working fine. Now I can leave this here in NZ as my holiday car!

Anybody having misfire issues, kindly check the code and for any codes, then this code I had 121 Height Adaptation Load Management (which is not well documented online at all) this error code was all due to the ASC MK20 ABS module having bad solder joints inside that made things intermittent!
Attached Thumbnails
Click image for larger version Name:	ABS3.jpg Views:	17 Size:	33.5 KB ID:	17794   Click image for larger version Name:	ABS2.jpg Views:	20 Size:	59.4 KB ID:	17795   Click image for larger version Name:	ABS4.jpg Views:	21 Size:	58.1 KB ID:	17796  

Click image for larger version Name:	ABS5.jpg Views:	17 Size:	28.1 KB ID:	17797  

Last edited by MisterM52; 10-08-2019 at 10:58 AM.
MisterM52 is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Knock sensors and mess under the intake project ElmoPerkins Engine 5 03-27-2017 06:15 AM
Raising ride height buzzboy Suspension 6 01-05-2014 05:02 PM
knock knock... what's that? cpatstone Engine 66 06-21-2011 11:26 PM
Knock Sensors robcarync Maintenance 8 02-18-2006 11:07 PM
PARTS: Coilover Kits for TIs cali-ti Knowledge Base 0 01-23-2006 12:39 AM


All times are GMT +1. The time now is 01:40 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2019, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 86.64 k/100.54 k (13.82%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.