318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Induction

Notices

Induction Superchargers, NO2 and turbos.

.
» Recent Threads
dual vanos engine into...
03-17-2013 08:11 AM
Last post by K2daalvin
Today 02:50 AM
3 Replies, 3,417 Views
(CA): Clubsport and DASC...
10-13-2019 11:48 PM
Last post by anassa
Yesterday 11:38 PM
3 Replies, 252 Views
Racecar Build -- '95...
10-14-2019 06:26 PM
Last post by anassa
Yesterday 02:11 AM
1 Replies, 260 Views
1996 318ti interior
10-14-2019 08:58 AM
Last post by Sphinxe
10-14-2019 11:02 PM
1 Replies, 227 Views
WTB: M-Tech Rear Bumper
10-14-2019 08:14 PM
Last post by peter*g
10-14-2019 08:14 PM
0 Replies, 112 Views
Happy Birthday hooverco
10-14-2019 06:17 PM
Last post by 1996 328ti
10-14-2019 06:17 PM
0 Replies, 120 Views
Selling 1995 318Ti...
09-29-2019 09:54 PM
Last post by BRADESTAR
10-14-2019 06:58 AM
3 Replies, 953 Views
1996 318ti interior door...
10-12-2019 01:38 PM
Last post by Sphinxe
10-13-2019 03:47 PM
3 Replies, 412 Views
Happy Birthday lazoh
10-13-2019 05:00 AM
Last post by 1996 328ti
10-13-2019 05:00 AM
0 Replies, 185 Views
1996 BMW 318ti for sale...
08-24-2019 07:43 AM
Last post by digitalat
10-12-2019 10:40 AM
1 Replies, 1,473 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 08-15-2017, 02:28 PM   #1
schiavonec
Junior Member
 
Join Date: Aug 2017
Location: Colorado
Posts: 8
iTrader: (0)
Default DASC install manual needed

Hello,

new to the forum and BMW. I recently purchased a 97ti with a M44 that has a DASC. It did not come with an install manual. Does anyone have one in electronic form? I am looking to evaluate the crank case ventilation routing and this differs from stock form.

Thanks,

Chris
schiavonec is offline   Reply With Quote
Old 08-15-2017, 06:39 PM   #2
cmoore
Senior Member
 
Join Date: Jun 2012
Location: philadelphia
Posts: 216
iTrader: (1)
Default dasc install

Contact Jim at Downing Atlanta. They are very helpful and should be able to email you a pdf. Just make sure he knows exactly which m42 or M44 versions you have. If he can't help I may be able to find one, depending on what year.
cmoore is offline   Reply With Quote
Old 08-15-2017, 08:56 PM   #3
schiavonec
Junior Member
 
Join Date: Aug 2017
Location: Colorado
Posts: 8
iTrader: (0)
Default

Quote:
Originally Posted by cmoore View Post
Contact Jim at Downing Atlanta. They are very helpful and should be able to email you a pdf. Just make sure he knows exactly which m42 or M44 versions you have. If he can't help I may be able to find one, depending on what year.
Thank you for the expeditious reply!

I left a voice message this am, and will follow up within a day or so if I don't hear back. I did not have a contact name so it may take a bit longer. I have a 97 with the M44. I am not clear on the model of the SC, but will take another look after work.
schiavonec is offline   Reply With Quote
Old 08-15-2017, 09:57 PM   #4
cmoore
Senior Member
 
Join Date: Jun 2012
Location: philadelphia
Posts: 216
iTrader: (1)
Default

I know I have the 97+ M44 manual. If you give me an email address , I can forward it to you.
cmoore is offline   Reply With Quote
Old 09-01-2017, 03:21 AM   #5
schiavonec
Junior Member
 
Join Date: Aug 2017
Location: Colorado
Posts: 8
iTrader: (0)
Default

Thanks for the offer. I was able to get it from the previous owner. I am still trouble shooting some vacuum and/or intake issues. There are stutters in the 2000 to the 2800 rpm range.

The PO did some valve work, the exhaust is also a larger diameter than stock, the SC pulley is the smallest available and the car has a performance chip. I've replaced some hoses, clamps, etc., and it has gotten better, but this is mildly annoying, and I want to get it perfectly smooth.

I believe the crank case valve is in need of replacement too and that will occur this weekend as it just arrived.

The other item to address is a lower than normal idle for the first 1-2 minutes, etc. Once up to standard running temp it is fine. The forum advice is a bit all over the board, and without seeing/feeling/hearing it, it perhaps isn't realistic to diagnose the issue from a keyboard.

Thanks again, and I hope to contribute to the knowledge base for others too.

edit - pulled everything off can cleaned thoroughly. It runs nicely now. It could have been a dirty MAF sensor.

Last edited by schiavonec; 10-11-2017 at 03:03 AM.
schiavonec is offline   Reply With Quote
Old 09-09-2017, 01:13 PM   #6
E30-M3
Member
 
Join Date: Aug 2017
Location: MA
Posts: 65
iTrader: (0)
Default

Sound like the chip is not for the system. Might need some dyno tuning to get running properly and have a proper tune for the DASC.
E30-M3 is offline   Reply With Quote
Old 09-09-2017, 09:51 PM   #7
1996 328ti
Senior Member
 
1996 328ti's Avatar
 
Join Date: Jun 2003
Location: Greenville, SC
Posts: 9,335
Vehicles
iTrader: (1)
Default

Quote:
Originally Posted by schiavonec View Post
Hello,

new to the forum and BMW. I recently purchased a 97ti with a M44 that has a DASC. It did not come with an install manual. Does anyone have one in electronic form? I am looking to evaluate the crank case ventilation routing and this differs from stock form.

Thanks,

Chris
If anyone needs one laterhttp://www.318ti.org/files/showentry.php?e=21&catid=1
__________________
...steven
BMW CCA #146825
1995 BMW 318ti Club Sport 1996 BMW 328ti 2003 MINI Cooper S
www.bmwcca.org

Last edited by 1996 328ti; 09-09-2017 at 09:53 PM.
1996 328ti is offline   Reply With Quote
Old 08-16-2019, 06:59 AM   #8
Alivinglegend
Junior Member
 
Join Date: Aug 2019
Location: Oregon
Posts: 5
iTrader: (0)
Default

Quote:
Originally Posted by 1996 328ti View Post
Hi, I have a DASC on my ti and I am in need of the installation manual. The site is telling me I don't have adequate permissions to download from the link above, I assume because i am a new user. Does anybody know where else I can find it?
Alivinglegend is offline   Reply With Quote
Old 09-06-2019, 03:09 AM   #9
Alivinglegend
Junior Member
 
Join Date: Aug 2019
Location: Oregon
Posts: 5
iTrader: (0)
Default

I think the forum will let me download it after 5 posts, but it sure is hard to rack up posts with how slow it is around here.
Alivinglegend is offline   Reply With Quote
Reply

Bookmarks

Tags
ccv , dasc , instructions , manual


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
New DASC install questions, pred Induction 1 05-22-2013 03:53 AM
DASC install questions pred Induction 6 03-11-2013 02:54 AM
DASC install photos 1996 328ti Induction 10 07-01-2010 12:31 AM
dasc install sabbath130 Induction 10 07-20-2005 02:05 PM
Just finished myh DASC Install. ZeroG Induction 16 04-01-2005 11:44 PM


All times are GMT +1. The time now is 03:15 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2019, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 98.94 k/116.86 k (15.33%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.