318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Suspension

Notices

Suspension Springs, sway bars, shocks.

.
» Recent Threads
1999 M-Sport For Sale
12-31-2023 05:10 PM
Last post by Coop540iT
03-23-2024 06:39 PM
1 Replies, 99,239 Views
Once again 318ti owner...
03-20-2024 12:39 PM
Last post by two30grain
03-22-2024 02:04 PM
1 Replies, 62,197 Views
What brakes do I...
03-20-2024 03:27 PM
Last post by huirtera
03-20-2024 03:27 PM
0 Replies, 59,464 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 12-14-2009, 02:15 AM   #1
UberWagen
Senior Member
 
UberWagen's Avatar
 
Join Date: Aug 2008
Location: Auburn, Alabama
Posts: 206
iTrader: (0)
Default Inside wear on rear tire. suggestions?

I'm a little new to the 318ti suspension. I'm used to VW's, and I've only had the car about a year. Anyway, on to my question. I'm getting pretty bad wear on the inside of my right rear tire. This car is bone stock, and the rear suspension has probably never been touched before. I have a Hanes manual for it, but this write-up for rear suspension is horrible. I see some sites they say the stock rear end is adjustable, or it isn't, or it is, but you need a special tool. That's not helping me fix my tire problem. SO. Am I looking at a ride height issue with a worn spring, a bent arm, worn bushings. OR!? Am I looking at just somehow adjusting the camber a little without having to buy a $400 fully adjustable camber kit. I know you can't give me exactly what it is, all I am looking for is if there are adjustments that can be made, or is something worn out? It's just my rear right, my rear left is fine.
UberWagen is offline   Reply With Quote
Old 12-14-2009, 03:14 AM   #2
cooljess76
NOBODY F's with the Jesus
 
cooljess76's Avatar
 
Join Date: Oct 2006
Location: Ventura California
Posts: 7,824
iTrader: (6)
Default

If everything is original, you're probably looking at a complete suspension overhaul. At least you should. I'm sure money is probably tight right now as it is for most people, but this isn't one of those things that suddenly goes bad. You'd expect any car to wear out after a hundred thousand miles. These things are over 10 years old now and things just wear out. Since only one side is wearing tires, you may be looking at a blown/worn shock, torn shock mount, a broken spring, a bent trailing arm, who knows. Judging by the way you asked for help, I'm guessing that you're not very mechanical, otherwise you would have looked under the car and figured out what the problem was. Perhaps you should take it to a shop and have an alignment done.
cooljess76 is offline   Reply With Quote
Old 12-14-2009, 03:27 AM   #3
spidertri
Senior Member
 
spidertri's Avatar
 
Join Date: Apr 2007
Location: Elizabeth City, NC
Posts: 3,877
Vehicles
iTrader: (9)
Default

On a stock ti, nothing in the rear is adjustable. On the front, only toe is adjustable.
__________________
~Dave~

98 328ti Morea Grun slicktop
11 128i space gray slicktop
13 JGC WK2 Deep Cherry

Search | RealOEM
spidertri is offline   Reply With Quote
Old 12-14-2009, 04:04 AM   #4
RAiMA
Senior Member
 
Join Date: Jun 2004
Location: Sydney, Australia
Posts: 593
iTrader: (0)
Default

As long as the car hasn't been lowered, there shouldn't be excessive tire wear on the insides.

I'd suggest going to get a wheel alignment done. Like the guys said, it won't be adjustable. They'll be able to measure if it's in factory spec or not. If it's not, it could have taken a nasty bump against a curb or something which may need bits of the suspension replaced to bring it back in spec.
__________________
RAiMA
Old RT E36 S/C'd 318ti Sports 13.318 @ 105.99mph
New RT E36 Turbo 328ti Sports 12.25 @ 123mph
BMW E39 528i Touring
Performance at its best
RAiMA is offline   Reply With Quote
Old 12-14-2009, 04:14 AM   #5
tiFreak
Senior Member
 
Join Date: Sep 2007
Location: asdfasdf
Posts: 10,002
Vehicles
iTrader: (8)
Default

just so you know, the Haynes manual only covers coupes and sedans, the hatchback has a completely different rear end setup
tiFreak is offline   Reply With Quote
Old 12-14-2009, 08:58 AM   #6
pdxmotorhead
Senior Member
 
Join Date: Mar 2005
Location: Portland Or
Posts: 2,666
iTrader: (1)
Default

If you go to a really good alignment shop, (Find one that supplies road racers if possible.)

They actually can align the rear, there are offset bolts, bushings etc available throught he aftermarket body supply chains.

My local shop actually had a gadget that straightened a bent trailing arm on a 911 I used to own.

Dave
__________________
Dave - PDX
1995 318ti - Active Black and Tan.
2005 330xi - Mtech 1 - 6spd - Orient Blue/Black
pdxmotorhead is offline   Reply With Quote
Old 12-14-2009, 09:46 PM   #7
UberWagen
Senior Member
 
UberWagen's Avatar
 
Join Date: Aug 2008
Location: Auburn, Alabama
Posts: 206
iTrader: (0)
Default

Quote:
Originally Posted by cooljess76 View Post
If everything is original, you're probably looking at a complete suspension overhaul. At least you should. I'm sure money is probably tight right now as it is for most people, but this isn't one of those things that suddenly goes bad. You'd expect any car to wear out after a hundred thousand miles. These things are over 10 years old now and things just wear out. Since only one side is wearing tires, you may be looking at a blown/worn shock, torn shock mount, a broken spring, a bent trailing arm, who knows. Judging by the way you asked for help, I'm guessing that you're not very mechanical, otherwise you would have looked under the car and figured out what the problem was. Perhaps you should take it to a shop and have an alignment done.
I appreciate the input. But I am pretty mechanically inclined. lol. But visually, everything is in spec. I've checked, everything is tight, bushings are good.
UberWagen is offline   Reply With Quote
Old 12-14-2009, 11:50 PM   #8
cooljess76
NOBODY F's with the Jesus
 
cooljess76's Avatar
 
Join Date: Oct 2006
Location: Ventura California
Posts: 7,824
iTrader: (6)
Default

Quote:
Originally Posted by UberWagen View Post
I see some sites they say the stock rear end is adjustable, or it isn't, or it is, but you need a special tool.
Quote:
Originally Posted by UberWagen View Post
Am I looking at just somehow adjusting the camber a little without having to buy a $400 fully adjustable camber kit.
Quote:
Originally Posted by UberWagen View Post
all I am looking for is if there are adjustments that can be made, or is something worn out?
Quote:
Originally Posted by UberWagen View Post
Am I looking at a ride height issue with a worn spring, a bent arm, worn bushings.
Quote:
Originally Posted by UberWagen View Post
I've checked, everything is tight, bushings are good.
Quote:
Originally Posted by UberWagen View Post
I am pretty mechanically inclined.

If you were mechanically inclined, you'd clearly see that there are no stock "adjustments" and there is no "special tool". Ireland Engineering makes an eccentric bolt kit that allows you to adjust the camber and it costs a lot less than 400 bucks. The fact that only one tire is wearing raises a big flag that says something is wrong that only affects one side. Something is either worn, bent, blown or broken, and we're not psychic.
cooljess76 is offline   Reply With Quote
Old 12-15-2009, 12:19 AM   #9
UberWagen
Senior Member
 
UberWagen's Avatar
 
Join Date: Aug 2008
Location: Auburn, Alabama
Posts: 206
iTrader: (0)
Default

Quote:
Originally Posted by cooljess76 View Post
If you were mechanically inclined, you'd clearly see that there are no stock "adjustments" and there is no "special tool". Ireland Engineering makes an eccentric bolt kit that allows you to adjust the camber and it costs a lot less than 400 bucks. The fact that only one tire is wearing raises a big flag that says something is wrong that only affects one side. Something is either worn, bent, blown or broken, and we're not psychic.
Thanks for the advice. And I realize your not sylvia brown. Part of the reason I haven't got a real good look at it is due to it raining for the past 2 weeks, I just took a quick glance in a parking garage-no garage at my house, just a carport-, and just maybe I thought somebody else would've had the same problem, possibly making it common. I think after building an engine, doing an engine swap, placing in a national mechanics competition, having taken several auto mechanics classes, I think I would know how to turn a wrench. Don't take that the wrong way, but just want to prove a point. I very much appreciate your suggestions.. Once this rain lets up I'll put it on the ramps.
UberWagen is offline   Reply With Quote
Reply

Bookmarks

Tags
camber , rear suspension , spring , tire wear


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
HELP! Tire wear, front camber plates, rear control arms Alexandre VTS Suspension 6 05-02-2008 01:08 AM
Rear Bushings Suggestions Watchmyradical Suspension 3 03-23-2007 12:47 AM
Rear Bumper Suggestions jonny116 Exterior 13 10-25-2005 04:43 PM
New rims - need tire suggestions riker Wheels and Tires 9 12-11-2004 10:25 AM
Tire suggestions tgroth Lounge 4 07-22-2001 09:43 PM


All times are GMT +1. The time now is 09:44 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 101.32 k/118.34 k (14.38%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.