» Site Navigation | | » Recent Threads | | | ![](http://www.318ti.org/forum/clear.gif) | ![Reply](http://www.318ti.org/forum/images/buttons/reply.gif) | ![Share/Bookmark](http://static.addtoany.com/buttons/share_save_171_16.png) | | 09-20-2009, 05:01 AM | #31 | Senior Member Join Date: Dec 2007 Location: Gulfport, Florida Posts: 3,208 | Quote: Originally Posted by Jean H.318TI well im gonna do whatever u think is better so i guess i would just keep the 14psi spring, and run 9psi DD and 14psi for FUNNN I was gonna use a electronic boost controller, what do u recomend? | Electronic all the way ![Tongue](http://www.318ti.org/forum/images/smilies/tongue.gif) Gizzmo MS-IBC is what I run and I love it. Swap the springs and put the 14psi spring in there, it's only 1 psi but worth it. By the way they are real fun to change by yourself so you might want someone to help you... If you got the same turbo as me you will need to make a little room for it. Grind the block casting a little and the bottom left motor mount bolt head needs to be cut down a little for perfect fitment. The block grind does not remove any material that is important as you will find when you do it. It's just an area were the casting is very thick and hits the exhaust housing on the turbo. Remember to make sure you get the correct down pipe bolt flange so you don't have to get changed like I did. The OBX manifold comes with the down pipe in the kit, that flange needs to be a standard 4 bolt turbo exhaust flange on that down pipe Also if you figure out how to install the waste gate dump pipe I want pictures since I was unable to get one on mine without firewall fabrication (too lazy to do it). My waste gate dumps right out the waste gate dump toward the back of the transmission....No worries since it doesn't dump much or for too long. 1,500 miles and no exhaust marks or burns anywhere from the dump... I think I'm going to have to go to church tomorrow ![Wink](http://www.318ti.org/forum/images/smilies/wink.gif) with the camera mounted inside so I can show you what 14.7psi is like. Remember my car is low compression so yours at the same boost will be a little more powerful. I'm sure you will have problems sleeping a night until your project is completed after you see this video Best, John S Last edited by xxxJohnBoyxxx; 09-20-2009 at 05:05 AM. | | | 09-20-2009, 11:03 PM | #32 | Senior Member Join Date: Apr 2007 Location: Auburn, WA Posts: 1,814 | this is the turbo manifold im gonna buy and i see a 4 bolt flange for the down pipe. is this the right 1? http://cgi.ebay.com/ebaymotors/OBX-T...Q5fAccessories i already have the 14psi spring on the wastegate and yeah is a PITA. can wait for the video and to be done with this project but i have to wait till i get money every month to buy the parts and stuff so is gonna take a long time, and i cant sleep already just by watching some videos of ur car with the 14psi dash and the first turbo start and missing my srt4 stage 2 __________________ 5/96 318TI Sport BIG TURBO | | | 09-21-2009, 02:43 AM | #33 | Senior Member Join Date: Apr 2007 Location: Auburn, WA Posts: 1,814 | done installing the turbo timer ![Rolleyes](http://www.318ti.org/forum/images/smilies/rolleyes.gif) works great and really easy install __________________ 5/96 318TI Sport BIG TURBO | | | 09-21-2009, 03:14 AM | #34 | Senior Member Join Date: Sep 2007 Location: asdfasdf Posts: 10,002 | cool, that will come in useful on your NA engine ![Razz](http://www.318ti.org/forum/images/smilies/icon_razz.gif) at least if you have someone else drive your car it will screw with them when they turn the key off | | | 09-21-2009, 03:25 AM | #35 | Member Join Date: Sep 2009 Location: Guatemala Posts: 42 | wow , great proyect | | | 09-21-2009, 01:55 PM | #36 | Senior Member Join Date: Dec 2007 Location: Gulfport, Florida Posts: 3,208 | Quote: Originally Posted by Jean H.318TI this is the turbo manifold im gonna buy and i see a 4 bolt flange for the down pipe. is this the right 1? http://cgi.ebay.com/ebaymotors/OBX-T...Q5fAccessories i already have the 14psi spring on the wastegate and yeah is a PITA. can wait for the video and to be done with this project but i have to wait till i get money every month to buy the parts and stuff so is gonna take a long time, and i cant sleep already just by watching some videos of ur car with the 14psi dash and the first turbo start and missing my srt4 stage 2 ![Sad](http://www.318ti.org/forum/images/smilies/icon_sad.gif) | Just from eyeing that it looks like the smaller flange and that is the same guy I bought my manifold from. I would ask him if that is a standard 4 bolt flange for a .63 exhaust housing before you purchase | | | 09-21-2009, 01:58 PM | #37 | Senior Member Join Date: Dec 2007 Location: Gulfport, Florida Posts: 3,208 | Quote: Originally Posted by Jean H.318TI done installing the turbo timer ![Rolleyes](http://www.318ti.org/forum/images/smilies/rolleyes.gif) works great and really easy install | Was that a 3 wire install? If so what 3 wire did you tap into. I tried it on mine and everything stays on but the EWS cuts the fuel and spark.... | | | 09-21-2009, 02:16 PM | #38 | Senior Member Join Date: Apr 2007 Location: Auburn, WA Posts: 1,814 | Yeah it was a 3 wire install, well actually 5, ground and e-brake safety (optional), just tap the red, green, and purple wire from the ignition on the steering column, So far the car stays on until whatever time the turbo timer says is gonna stay on and then turns off when the time's up, I can even lock the car and roll up the windows and stuff and the car keep runing just fine, hope this can help __________________ 5/96 318TI Sport BIG TURBO | | | 09-21-2009, 02:26 PM | #39 | Senior Member Join Date: Apr 2007 Location: Auburn, WA Posts: 1,814 | I have pics of the whole process (turbo timer install) maybe some1 can write a nice HOW TO, just let me know and I can send the pics __________________ 5/96 318TI Sport BIG TURBO | | | 09-21-2009, 02:26 PM | #40 | Senior Member Join Date: Dec 2007 Location: Gulfport, Florida Posts: 3,208 | Quote: Originally Posted by Jean H.318TI Yeah it was a 3 wire install, well actually 5, ground and e-brake safety (optional), just tap the red, green, and purple wire from the ignition on the steering column, So far the car stays on until whatever time the turbo timer says is gonna stay on and then turns off when the time's up, I can even lock the car and roll up the windows and stuff and the car keep runing just fine, hope this can help | I will look at mine again. I did the 5 wire. Maybe I swapped green and purple and thats the problem. IDK If you got it working, I must get mine working | | | 09-21-2009, 04:56 PM | #41 | Senior Member Join Date: Dec 2007 Location: Gulfport, Florida Posts: 3,208 | [QUOTE=Jean H.318TI;244818] can wait for the videoQUOTE] Sorry, reality took over. I get off probation on the 30th and I just could not do it. If I'm caught on the road for anything other then "business purpose" I'm in deep $hit. If I can't drive to work I loose everything, without money I'm nothing and my family needs me paying bills. I could be hit by a old lady and it's my fault. Break down and I'm busted. I'm keeping it super clean and doing exactly what they told me to do so I can get off probation in 9 days and my class "E" license back in February. I completely stopped racing anyone for the past 4-5 days, I don't know how long I can hold out but it's like AA "one day at a time"... | | | 09-21-2009, 05:49 PM | #42 | Senior Member Join Date: Apr 2007 Location: Auburn, WA Posts: 1,814 | Don't worry about it just wait until u get ur license back and don't get in any more trouble __________________ 5/96 318TI Sport BIG TURBO | | | 09-21-2009, 08:02 PM | #43 | Senior Member Join Date: Nov 2007 Location: Rocky Hill, CT Posts: 1,065 | Jean, looks like the parts collecting is progressing nicely ![cool](http://www.318ti.org/forum/images/smilies/cool.gif) I'm excited to see the build start, and jealous too John, I agree, don't push your luck. Screw the car not getting used if you lose your license, the family's always more important, and I'm glad you realized racing on the suspended license was no better than being one of the super tuners blocking off streets __________________ 1995 318TI base. 95 2.5L from 325IS. S50 cams+pistons, e36 M3 front brakes. H&R race springs F+R. Turner Motorsport front sway bars, M3 control arms. M Roadster rear sway bar. Racing Dynamics strut brace. e36 325i 5spd. 3.25lsd from e28 535is. M Roadster short shifter. Conforti chip. | | | 09-22-2009, 11:13 PM | #44 | Senior Member Join Date: Apr 2007 Location: Auburn, WA Posts: 1,814 | Got my turbo today ![Rolleyes](http://www.318ti.org/forum/images/smilies/rolleyes.gif) and that sucker is BIG __________________ 5/96 318TI Sport BIG TURBO | | | 09-22-2009, 11:48 PM | #45 | Senior Member Join Date: Mar 2005 Location: NJ Posts: 1,625 | good luck - sounds good. boost is really the trick! my car, though still with some stuff to ironed out, is like nite & day compared to what it was when I got it. anything past 10 psi & that 2.25 inch exhaust will make a difference, too. Believe it or not, I'm actually going custom route & will be getting the 2.5 inch wiht a Magnaflow back box soon! LOL Quote: Originally Posted by Jean H.318TI well as some of u guys know i always wanted to turbo my lil TI but never really have some1 with a good tunning but now that johnboy is done with his turbo and running good im gonna get on this and start the turbo build, is not gonna be even close to what johnboy have but is good for me. gonna use the same OBX turbo manifold HKS Super SQV TIAL wastegate 44mm MITSUBISHI turbo T3 HKS turbo timer 27"x7"x2.5" intercooler delta fin 2.5" in/out. - black 2.5" intercooler piping - black, Silicone hoses black Heavy Duty Spring Loaded T-Bolt Clamps Turbo Oil Scavenge Pump electronic boost controller (not sure what brand) Lucas 42.8# Blue Strip injectors Injector adaptors (Metric) M3 MAF sensor 2.5" > 3" boot to connect new MAF in system. Co2 intercooler sprayer (no tune) just to help with the heat soak on hot days or before/after a run on the track/street and all the other random stuff like the oil/water lines and everything else and im also gonna run with open wastegate, so is gonna be super loud (only WOT) lol is gonna take few months until i get all the parts, i already order some of the stuff tho, so maybe by winter or before we are gonna have another turbo TI ![Rolleyes](http://www.318ti.org/forum/images/smilies/rolleyes.gif) and im only gonna run 14psi tops and 8psi DD (shooting for 200+whp @14psi) cant wait for this to be done but money is kinda low, around 400month to spend on this so yeah is gonna take some time, any donations are welcome ![Wink](http://www.318ti.org/forum/images/smilies/wink.gif) | __________________ ![http://i254.photobucket.com/albums/hh98/damiennn666/318ti5-1.jpg?t=1217269847](image.php?s=c857817a69e680cb71091c0cebb9634a&u=1514&type=sigpic&dateline=1217252517) SOLD!SOLD!SOLD!SOLD!SOLD!SOLD!SOLD!SOLD! Metric Mechanic's 2.0 stroker/258' intake cam/42 lb. inj./remap/HD fuel pump /DASC w.3' pulley @ 15psi/SNOW System/3.45 LSD/Billstein PSS coils /Stromung Exhaust/DS1's/X-Brace/Front & Rear H&R Sways/OMP 300mm SW /SAP delete/ASC+T delete/Hayabusa valve springs/MM's LTW flywheel | | | ![Reply](http://www.318ti.org/forum/images/buttons/reply.gif) | | Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | | Posting Rules | You may not post new threads You may not post replies You may not post attachments You may not edit your posts HTML code is Off | | | |