318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Induction

Notices

Induction Superchargers, NO2 and turbos.

.
» Recent Threads
1996 332ti supercharged...
06-08-2019 08:27 PM
Last post by juice2000
Today 04:17 AM
3 Replies, 800 Views
Rudolph the Red 318ti
05-06-2019 10:49 PM
Last post by MisterM52
Yesterday 10:45 AM
20 Replies, 3,068 Views
Hi All
06-23-2019 03:50 PM
Last post by MisterM52
Yesterday 10:40 AM
5 Replies, 408 Views
Ultimate Supercharger...
06-23-2019 08:06 AM
Last post by MisterM52
Yesterday 03:21 AM
6 Replies, 521 Views
BMW Individual Interior...
05-14-2019 04:38 PM
Last post by runnr548
06-24-2019 11:45 PM
3 Replies, 905 Views
Odd starting issue after...
06-10-2019 03:48 PM
Last post by paul somlo
06-24-2019 08:43 PM
8 Replies, 745 Views
Swap Manual Q&A
01-09-2007 03:32 AM
Last post by J!m
06-24-2019 06:48 PM
206 Replies, 64,707 Views
As Green as the Touge - ...
06-18-2016 02:47 PM
Last post by anassa
06-24-2019 05:04 PM
45 Replies, 24,095 Views
How much is too much $...
06-22-2019 10:31 PM
Last post by anassa
06-24-2019 04:03 PM
2 Replies, 414 Views
E8x Rear Subframe Rust
06-23-2019 04:31 PM
Last post by OllieNZ
06-23-2019 04:31 PM
0 Replies, 223 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 05-03-2008, 11:45 PM   #1
Christian
Member
 
Join Date: Mar 2008
Location: West Palm Beach, FL
Posts: 30
iTrader: (0)
Default New DASC installed - Need help!

A few weeks ago I installed a DASC on my Z3 1.9. At the same time of the initial installation I installed Technique's Tuning stage 3 kit (DME reflash, larger injectors, and 3" MAF). The Stage3 kit does away with the DASC's rising rate fuel pressure regulator since the software allows for larger injectors. The stock boost was fairly low so I installed a 3.6" pulley and now get 9 lbs of boost.

After the installation the car cranked fine, idled fine, and drove great, but just didn't seem very powerful in comparison to other DASC cars I've driven. I dyno'd the car today and found a few issues. Max HP was 164 and torque under 140.



The first dyno pull is shown. On the second dyno pull the car misfired. I haven't felt that on the street, but it certainly showed on the dyno graph. I'm going to pull the plugs and start trying to find the reason for the misfire. I'm running new NGK Iridium IX plugs. They are heat range 7 and gapped at .032".

I scanned the computer and found a fault code for the MAF (code PO100). I cleared the code and it didn't throw the code again on the 5 mile drive home. When I first installed the MAF a few weeks ago I installed it backwards, and I idled the car like that for about five minutes. Maybe that's why the fault code was there. If the code comes back I guess I have a faulty MAF.

I don't think the Technique Tuning software is causing the rich condition since this is the same programming Nick has used on many other cars, but I emailed him to get his input as well.

The dyno operator said that the Mustang dyno they have is conservative compared to some others, so some of the low power numbers could be attributed to that, but it doesn't explain they the car runs so rich up top.

I need to start trying to identify and correct any issues, so please let me know your input. Does anyone have any ideas where I should start?

__________________
Christian is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
A/C wont start - checked _everything_!! NeoP HVAC 5 10-26-2008 08:48 AM
Just checked on my car at the paint shop bluesteel Exterior 18 08-29-2008 04:34 AM


All times are GMT +1. The time now is 06:42 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2019, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 61.86 k/71.26 k (13.19%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.