318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Engine Swaps

Notices

Engine Swaps Engine conversions.

.
» Recent Threads
1999 M-Sport For Sale
12-31-2023 05:10 PM
Last post by Coop540iT
03-23-2024 06:39 PM
1 Replies, 96,092 Views
Once again 318ti owner...
03-20-2024 12:39 PM
Last post by two30grain
03-22-2024 02:04 PM
1 Replies, 59,103 Views
What brakes do I...
03-20-2024 03:27 PM
Last post by huirtera
03-20-2024 03:27 PM
0 Replies, 56,445 Views
M50+manual swap bastard...
03-01-2024 11:00 PM
Last post by Andy318
03-18-2024 02:34 PM
3 Replies, 131,419 Views
  Share/Bookmark
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 05-22-2017, 05:28 PM   #1
95///M3
Junior Member
 
Join Date: Dec 2016
Location: York, PA
Posts: 16
iTrader: (0)
Default First N52 Swap - 1997 AlaskaBlau 318ti N52 6Spd

First, allow me to take a few moments to thanks everyone involved in this project and explain why we decided to pursue this endeavor. First off thank you to Mr. C for finding the chassis on Craigslist whilst searching for BMW motorcycles. Thankfully the seller included the keyword "motorcycle" as he was open to trades. We probably wouldn't have stumbled on the 318it (sic) if it wasn't for the trade opportunity keyword. The 3 main players to actually perform the work were: Kassel Performance in York, PA, BimmerBuddies in Middletown, PA, and Chris S. of BimmerLabs in WA. All 3 were critical in actually taking the idea of swapping the N52 into the E36 318ti shell.

How it all happened: As previously mentioned we found the shell on CL with 50k original miles. It was a factory Alaska Blue MTech automatic with an overheated M44. This presented an ideal shell for our project. We considered intially swapping an S52, S54, N54, N20, but the N52 prevailed for several reasons. Number one, it was going to be a challenge. To our knowledge no one has successfully run the N52 in any other chassis than it was originally designed to be in, while utilizing the stock ECU and no other associated modules. Aside from the electronics, the electric water pump, power steering, 6speed, etc, all posed new hurdles to overcome. The following post will help to describe the process and I will do my best to answer any questions.

The second reason to swap the N52 was for efficiencies. The 318ti represented efficiency. It was an affordable, practical, light, nimble, spacious compact and we intended to maintain this factory feel only with a modern drivetrain. The aluminum/magnesium N52 actually weighs less than the iron block M44 that was pulled from the shell. The electric water pump removes parasitic loss from turning the belt driven pump on the M44. The new alternator has a clutch design intended for again less parasitic draw and better overall MPG. In stock form the N52B30 makes a healthy 231HP and is rated at 29MPG on the highway. Our power goals were quite higher than the stock 325 output and we were able to achieve nearly a 70HP gain due to hardware and software changes.

On to the actual specifics of the swap!

Vehicle started as a 1997 AlasakaBlau Mtech - Auto. Purchased with a bad M44 and wanted to build something unique.





We started searching for a drivetrain and landed on a 2006 Z4 3.0si The full car was purchased as we thought it would be ideal to have the entire car so we could utilize as much or little as we needed. The Z4 was purchased as a base as it is more similar to the E46 which is similar to the E36.





Entire drivetrain was pulled from Z4 to start:



N52 without beauty cover on stand. Now was a good time to replace valve cover gasket, spark plugs, coils, headers, ccv components, oil pan gasket, etc. The E90 power steering pump, idler, and belts were installed as well since the Z4 uses the servotronic steering:





After removing the engine from the stand, we decided to use a new single mass flywheel conversion from Valeo along with a sprung clutch disc. The original flywheel had some unwanted play in it and though it would be a good idea to replace. We wanted to use the 6 speed manual, so we bolted the 6 speed to the engine and carefully lowered the assembly into the ti. It was a very tight fit with the transmission attached but it did indeed clear without any contact to the body.



The engine nestled into the E36 bay very nicely. We wanted it to sit as close to the firewall as possible so we ran stock mounts rotated 180 degrees onto the Z4 engine arms. A transmission bracket kit was fabbed for the 6 speed and can now be purchased from Kassel Performance. The stock 318ti rear driveshaft was used along with a stock front Z4 auto shaft and guibo. In the photos below, a stock 6 cylinder airbox was mocked up and later replaced with a modified version of the Z4 airbox.





Mechanically, this pretty much sums up the actual fitting of the drivetrain into the ti: N52, new stock motor mounts rotate 180 degrees, stock 6 speed transmission, ti rear portion of driveshaft with Z4 auto front half. The small case diff was also changed out for a built 3.46 with the Thayer 3 clutch pack kit. New finned MZ3 cover was installed as well.



Moving onto hydraulic things. As mentioned above, the Valeo SMF kit was used. A custom short shifter from and clutch line were supplied by Rogue Engineering. Manual pedal box and new OE hard lines were installed from a manual 318ti. E36 M3 clutch master and E90 330 slave cylinders were used. A new larger bore E36 M3 brake master was also installed. One of the brake line fittings needed to be switched at the brake master to accommodate the M3 part. We used a new fitting and re-flared the line.

The brakes were upgraded to E46 M3 front calipers and rotors. The caliper brackets were machined in order to be a direct bolt on to the E36 318 front hub. No other modifications were required to the front brakes other than longer lines and new Akebono pads. The rear brakes were upgraded to Z4 calipers and rotors. All brake components were sent out to Renewed Finishes in PA for a full rebuild and powder coat. The M3 brakes fitting nicely under stock 17" M Contours:



Steering. We used the E90 330 steering pump, idler, and belt. The Z4 did not have a belt driven pump. New E36 328i lines were used along with new power steering reservoir. Everything was mounted to existing tabs on the chassis. Easy enough.

Cooling. The cooling system required some thought. An E36 M3 radiator was used in the stock location. In order to keep the rad as close to the support as possible, the rubber inserts in the mounts were not used. (The fit from the crank hub to the radiator is very tight.) A Z3 expansion tank was mounted where the existing windshield washer reservoir was on the 318 and a bracket was made to hold the expansion tank. The front lower hose from the expansion tank was capped. An E90 manual xi crossover tube was used. The lower radiator hose consisted of modifying the lower Z4 radiator hose. The upper radiator hose was a bit tricky. We cut up a new 630 N52 upper hose. Mainly we needed the quick connect fitting at the top of the engine. This fitting was used as it also had a lower fitting that would supply hot coolant to the heater core. Z4 heater core lines were used along with a random other bit of line that we needed to get back to the Z3 expansion tank. Image of cooling system on N52 to show the flow and electric water pump:



The Z4 ECU controlled electric fan was then used. The upper bracket portion needed to be lightly trimmed as it made contact with the small factory oil cooler. *The engine mounted oil-to water heat exchanger is very much optional and is not required. The fan was wired per the E90/Z4 and is controlled via the ECU.

Fueling. The stock fuel pump was replaced by a drop in Walbro 255 provided by Kassel. The machined sleeve is manufactured to drop into the stock hanger with no modificaiton. An E46 M3 S54 fuel pressure regulator and fuel filter were used ad mounted in the stock E36 location. The fuel pressure regulator from the M3 was used as the E90 uses an intank 5bar regulator. The M3 regulator is also has a 5 bar diaphragm and is a return style with a single feed line to the N52. A longer quick connect fuel line from the regulator to the fuel rail was used as the stock E90/Z4 hose was too short.

Last edited by 95///M3; 05-22-2017 at 05:32 PM.
95///M3 is offline   Reply With Quote
 

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
318ti 1.9l to 2.8l swap questions?? 318teeeye Engine Swaps 32 03-07-2011 09:24 PM
MA 1997 318ti w/California Top For Sale jac_buffalo US and North America 1 11-12-2010 05:09 PM
PA 1997 318ti with 97k dotmobiman US and North America 2 06-09-2010 02:30 PM
FS: 1997 318ti M-pack with full S52 swap e34biturbo US and North America 5 11-21-2008 11:33 PM
totaled m3 want to swap powertrain into 318ti need info thunder Engine Swaps 8 09-09-2005 05:34 AM


All times are GMT +1. The time now is 12:03 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 166.24 k/174.91 k (4.96%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.