318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Suspension

Notices

Suspension Springs, sway bars, shocks.

.
» Recent Threads
Knock Sensor Error &...
07-07-2019 05:42 AM
Last post by MisterM52
Today 01:39 AM
11 Replies, 889 Views
Learning to drift
06-29-2019 09:11 PM
Last post by andakn
Yesterday 01:34 PM
1 Replies, 677 Views
Ultimate Supercharger...
06-23-2019 08:06 AM
Last post by thenjnick
07-20-2019 11:34 PM
60 Replies, 6,408 Views
Rudolph the Red 318ti
05-06-2019 10:49 PM
Last post by MisterM52
07-20-2019 03:44 AM
28 Replies, 5,475 Views
Help on replacing ‘96...
07-19-2019 04:11 PM
Last post by Denteen
07-19-2019 08:22 PM
2 Replies, 348 Views
M44 Supercharged Project...
04-07-2019 06:54 AM
Last post by steve f
07-19-2019 01:46 AM
9 Replies, 1,936 Views
Oil Filter Housing Leak...
02-14-2008 08:21 PM
Last post by shriberone
07-18-2019 09:59 PM
119 Replies, 85,209 Views
H&R Race springs and...
06-26-2019 09:46 AM
Last post by Denteen
07-18-2019 12:07 AM
1 Replies, 842 Views
97' M-Tech Edition...
08-30-2018 06:51 PM
Last post by dudecati
07-17-2019 11:06 PM
13 Replies, 3,327 Views
1996 332ti supercharged...
06-08-2019 08:27 PM
Last post by slowoldpoop
07-16-2019 07:59 PM
6 Replies, 1,968 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 03-31-2019, 06:00 PM   #1
B1p0larbear
Junior Member
 
Join Date: Jun 2018
Location: Texas
Posts: 11
iTrader: (0)
Default Front camber plates

So I'm doing a fairly budget suspension overhaul on my 95 ti with 274k on it. The whole front end felt like it was going to fall out at any moment. So new control arms and bushes are fitted along with new tie rod ends at this point. I ordered a set of budget coilovers that I thought came with camber plates but it got here and I was mistaken. (I passed on the maxpeedingrods and went with tieftech, sold by hottuning on Ebay. Will give thoughts after they are instaled)

So now to my question, has anyone used the maxpeedingrods camber plates? I'm sure they are not great but like I said before I'm trying to keep the budget low. Are they total junk that I should pass on or are they good enough for a street car? Not planing on tracking the car just want to have a good tight street car.

Sent from my SM-G930V using Tapatalk
B1p0larbear is offline   Reply With Quote
Old 04-14-2019, 02:03 AM   #2
B1p0larbear
Junior Member
 
Join Date: Jun 2018
Location: Texas
Posts: 11
iTrader: (0)
Default

Well ordered the cheap camber plates this morning so with any luck will be pulling the reinforcements for my v8 coupe project and installing the coilovers on the ti. I'll post pics and updates after install.

Sent from my SM-G930V using Tapatalk
B1p0larbear is offline   Reply With Quote
Old 04-22-2019, 05:45 AM   #3
B1p0larbear
Junior Member
 
Join Date: Jun 2018
Location: Texas
Posts: 11
iTrader: (0)
Default Install completed

Alrighty, had the day off on Friday so I drove into the coilover install. At first glance all of the budget parts look to be pretty good and most of the fitment went great. In fact the fronts nearly installed themselves, the rears however I have a bit of a problem with. The id of the adjustment plates were a bit to small, so I ended up installing the rear springs upside down with the height adjusters on the control arm rather than on the upper spring mount. This makes adjustment a bit more troublesome but dosnt seem to have any effect on the drivability.

I set it at about a 1.5 inch drop, witch is as low as I can go without installing wheel spacers(will get final measurements after the springs have settled for a week or so). I was aiming for 1.5 anyway so I'm not offended in the least, just wanted to put it out there if someone wanted to use the same kit( using 16x6 inch wheels of an e46)

Have put 30ish miles on it so far and have not had a computer alignment done yet but did the best I could with a tape measure and a square. So far i have no major problems, just the standard pops that come with budget coilovers (think i will get some washers and thrust bearings for the front to fix that). The ride is very good, stiff but not harsh. I spent lots of time researching spring rates from the various manufacturers and found that this set was the softest, and for my taste and goals for the car it seems to be a great option.

Parts list:
Coilovers- Ebay, hottuning for e36/5 $274
Camber plates- Ebay, maxpeedingrods for e36 $37
Rear shock mounts- Amazon $20
Front and rear reinforcements- taken from project car
Attached Thumbnails
Click image for larger version Name:	20190419_122800.jpg Views:	22 Size:	73.3 KB ID:	17565   Click image for larger version Name:	20190419_123824.jpg Views:	20 Size:	47.0 KB ID:	17566   Click image for larger version Name:	20190419_133228.jpg Views:	19 Size:	50.9 KB ID:	17567  

Click image for larger version Name:	20190421_175112.jpg Views:	21 Size:	46.4 KB ID:	17569  
B1p0larbear is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Undefined vmaxx compact coilovers and bavauto camber plates fs/ft trav3000 Parting out & Parts (US) 0 06-20-2015 09:26 PM
Budget Friendly Camber Adjustment Parts? mamba Suspension 7 10-14-2014 06:07 PM
Misc parts IE E36 Camber plates for Sale BlackBMWs Parting out & Parts (US) 0 01-24-2013 10:21 PM
Adjustable Rear Camber Bushings DustenT Suspension 6 10-04-2006 05:37 PM
Positive camber! shaggy318ti Suspension 1 08-08-2006 08:34 PM


All times are GMT +1. The time now is 03:00 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2019, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 74.67 k/86.11 k (13.29%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.