318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Knowledge Base


Knowledge Base How to articles and things explained.

» Recent Threads
unfinished supercharged...
06-22-2021 03:57 PM
Last post by Spartan 059
Yesterday 07:07 PM
4 Comments, 5,028 Views
'95 Boston Green, ALL...
06-29-2021 04:24 PM
Last post by irdave
Yesterday 02:21 AM
10 Comments, 2,917 Views
New to the group
05-30-2021 05:47 AM
Last post by FunElan
Yesterday 12:02 AM
4 Comments, 2,089 Views
What model ti do you own?
02-26-2003 03:40 AM
Last post by sarinasr75
07-26-2021 02:40 PM
340 Comments, 172,822 Views
Longtime lurker via...
07-26-2021 07:33 AM
Last post by primo107
07-26-2021 07:33 AM
0 Comments, 118 Views
Happy Birthday ...
07-26-2021 05:00 AM
Last post by 1996 328ti
07-26-2021 05:00 AM
0 Comments, 105 Views
WTB: 318ti clubsport in...
05-21-2021 02:08 PM
Last post by jasminemicheal
07-23-2021 11:55 AM
6 Comments, 2,663 Views
WTB: Manual 318ti
05-17-2021 09:34 PM
Last post by jasminemicheal
07-23-2021 11:54 AM
3 Comments, 2,511 Views
WTB: M-Tech molding
06-25-2021 02:07 AM
Last post by jasminemicheal
07-23-2021 11:54 AM
3 Comments, 3,813 Views
07-23-2021 11:53 AM
Last post by jasminemicheal
07-23-2021 11:53 AM
0 Comments, 132 Views
Tutorial Tools Display Modes
Prev Previous Post   Next Post Next
M44 A/C Compressor Bracket DIY
M44 A/C Compressor Bracket DIY
Published by lokister
Default M44 A/C Compressor Bracket DIY

Hey everyone,

I chose to write this DIY because I had a hell of a time replacing this bracket with no other clear DIYs nor a Bentley manual that accurately depicts the compressors we have on our M42/M44s.

I broke the mount point on the bottom of the bracket for the A/C belt tensioner during a belt job in October. The mount is made of aluminum and is easy to break if the bolt holding the tensioner pulley is over-tightened.

The diagrams on RealOEM and in the Bentley do NOT accurately depict this repair. Once the initial mystique was removed from the job (thanks in part to members on this lovely forum), it was an easy repair.

Tools needed:
  • 6mm hex bit (a long one -- I used a ball-head long bit from Home Depot)
  • 8mm hex bit
  • 13mm socket
  • Torque wrench
  • Rachet strap

Materials needed:
  • New A/C compressor bracket (64-55-1-739-627)
  • (Optional) 4x hex bolt (07-11-9-904-533)
  • (Optional) 1x hex bolt (07-11-9-912-570)
  • (Optional) 3x allen bolt (I don't know the part number)


#1. Drive your beloved car onto ramps or jack up and place on jack stands. This job does not require that the wheels be removed, so whatever you prefer works. I will note that using ramps makes it slightly easier to "hold" the compressor up during bracket removal.

#2. If applicable, remove the A/C accessory belt. Turn the tensioner to the right to loosen it using an 8mm hex bit. Remove the hex bolt holding the tensioner pulley in place from the bracket. In my case, the entire tensioner was already broken, so I could skip this step.

#3. Remove the top allen bolt holding the compressor to the bracket using the long 6mm hex bit. I would recommend removing this bolt first to allow the weigh of the compressor to be distributed to the bottom bolts first. Trying to remove this top bolt when all the weight of the compressor is being supported by it is definitely not fun.

The bolt is located on the rear of the bracket, above the subframe and steering rack.

Step 1a1.jpg

The bolt is invisible from below, so it helps to (1) use the long hex bit and (2) have a thin smartphone handy (like a newer generation iPhone) to take intermittent photos to "guide" the bit into the bolt head.

Step 1a.jpg

Step 1b.jpg

When the bolt is removed from the compressor, it will still not be free from the bracket due to the positioning of the refrigerant lines. It will sit in the threaded hole of the bracket, but the compressor will nonetheless be free.

Step 1b2.jpg

Continued . . .
Tutorial Tools



Currently Active Users Viewing This Tutorial: 1 (0 members and 1 guests)
Tutorial Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Tutorial Tutorial Starter Category Comments Last Post
318ti use Z3 DME for SAP delete and emissions delete new318tifan Engine 6 12-19-2020 08:19 PM
M42/44 / 318ti Valve Cover Gasket DIY. PICS! CirrusSR22 Knowledge Base 93 11-13-2018 02:25 AM
A/C doesn't work hotmilk400 HVAC 6 07-05-2012 05:50 PM
Sold the wrong oil pan HELP! fast2002 Maintenance 4 01-27-2012 04:16 AM
Midnight Tuning Solutions OBD1 DIY BMW Live Tuning Kit bmwconnect Engine 61 10-11-2011 03:49 AM

All times are GMT +1. The time now is 09:13 PM.

Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2021, 318ti.org

Tutorial powered by GARS 2.1.8m ©2005-2006
© vBadvanced CMPS v3.2.2
[page compression: 89.44 k/100.27 k (10.81%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.