318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Knowledge Base


Knowledge Base How to articles and things explained.

» Recent Threads
WTB: S50/S52 swapped or...
08-29-2021 05:22 PM
Last post by 98332
Yesterday 03:23 PM
9 Comments, 7,210 Views
Central wood panel
08-22-2021 08:49 PM
Last post by andre3
01-20-2022 12:06 AM
2 Comments, 3,480 Views
95 318ti 5-Spd w/factory...
10-15-2021 08:22 PM
Last post by Mongwit
01-15-2022 08:05 PM
10 Comments, 9,270 Views
Rear Hatch cargo cover
03-08-2012 09:13 PM
Last post by vee030
01-14-2022 11:10 AM
34 Comments, 10,498 Views
Club Sport Red Millpoint...
01-04-2022 10:29 PM
Last post by J!m
01-14-2022 12:53 AM
3 Comments, 1,036 Views
Rhodes Racing Cage -...
07-25-2019 04:32 PM
Last post by saxman0321
01-13-2022 11:30 PM
4 Comments, 36,290 Views
Thoughts on 135 manual...
01-13-2022 03:41 PM
Last post by BMWChrisInVA
01-13-2022 03:44 PM
4 Comments, 302 Views
Tutorial Tools Display Modes
Prev Previous Post   Next Post Next
Installing Thule Roof Rack without Fit kit 225
Installing Thule Roof Rack without Fit kit 225
Piece Together Kits 145 and 2178
Published by blndweasel
Default Installing Thule Roof Rack without Fit kit 225

Hey Folks,

After months of poring over posts about discontinued 225 fit kits, and possible suggestions of piecing together the necessary parts from other fit kits, I have successfully mounted a Thule roof rack on my ti.

Basically, you start with fit kit 145 (E36 Sedan) and fit kit 2178 (Dodge Magnum). Fit kit 145 includes (4) of the front brackets you will need. Fit kit 2178 includes the #100 rear brackets you need.

If you look at the documentation for the 225 kit, you should use this for the measurements for the front and rear bar width, as well as the 700mm bar spacing (length wise on the vehicle).

Now the 225 kit shows a special rubber mount pad for the rear, which has this little protrusion to fit into the roof channel. This pad is completely unnecessary, from my experience. Use the flat pads included in the 145 kit, and they work fine. See photo for mounting example:

Alternatively, you could use the pads included in the 2178 kit, and just shave off the excess piece that is designed for the dodge magnum roof channel, leaving you with a flat pad nearly identical to the ones in kit #145.

On the front brackets, be sure to go with the measurements from the 225 kit. I noticed a discrepancy between the instructions for the ti and the E36 sedan (which is ridiculous of course), so go with the ti measurements. They are slightly narrower, keeping the mount pad up on the roof panel, and not overlapping with the roof channel. Also, if you use the measurements from the E36 sedan, the clips won't properly engage. So again, go with the 225instructions. just google Thule Fit kit 225. Perhaps we should grab a set of the PDFs to have on hand, in case Thule pulls those papers from the web, seeing as the kit is discontinued.

Front bracket:

Lastly, I decided to mount a Peloton bike rack. The problem is that it is too long for the ti, if you open your back hatch, it will hit the rack. So you have to cut off about 3-4" of the rear section of aluminum channel. I taped off a line with blue painters tape, then hacked it off with a fine-tooth hack saw. I then re-drilled the retention hole for the rear cap. See clearances below:

So there you have it. The best looking roof rack for the ti, purchased from rackattack.com, and with the savings I got from buying it there, it made up for the extra $60 I had to spend on a second fit kit. Total cost was just a hair over $600.

I have extra parts left over. Namely, a second set of front brackets, and the extra set of brackets from the dodge magnum. Not sure if these can be used for anything, but it looks like modification is possible. I'm going to play with that next.

In the mean time, if anyone is interested in doing this, and wants my front brackets from the 145 kit, I'll sell them for $30 including the pads from the magnum which can be modified for the ti. This will split the difference with someone for the added cost of piecing together the two fit kits.

The rack is great, mounts sturdy, only makes a little bit of whistling noise with the front spoiler installed, and just looks cool. I can't wait to go hit some muddy single tracks now.

If you have any questions, let me know and I will follow up.


the blonde weasel
Tutorial Tools



Currently Active Users Viewing This Tutorial: 1 (0 members and 1 guests)
Tutorial Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Tutorial Tutorial Starter Category Comments Last Post
thule roof rack question gitthatcrew Lounge 8 12-17-2009 06:16 AM
WTB: Thule rack or fit kit 225 Mauriceman US and North America 18 02-23-2009 07:51 AM
WTB: roof rack or Thule fit kit chrissummit US and North America 3 09-03-2008 04:57 PM
Thule luggage rack fit kit for bmw 318ti TippyMcStagger US and North America 5 05-12-2008 07:52 PM
Thule Roof Rack chrispycracker eBay and Craig's list listings 0 03-12-2007 04:20 AM

All times are GMT +1. The time now is 11:54 AM.

Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2022, 318ti.org

Tutorial powered by GARS 2.1.8m ©2005-2006
© vBadvanced CMPS v3.2.2
[page compression: 112.31 k/122.55 k (8.35%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.