Forum: Cars for Sale 11-30-2016, 02:55 PM |
Replies: 7 Views: 7,599 |
Forum: Induction 02-01-2013, 09:49 AM |
Replies: 17 Views: 20,584 |
Forum: Induction 08-12-2012, 09:03 PM |
Replies: 3 Views: 2,025 |
Forum: Induction 08-11-2012, 12:38 PM |
Replies: 3 Views: 2,025 Strange galletto issue Hi all Been trying to get my galletto tool to work so I can look to get it mapped. I started off by downloading the standard map off the ECU, then I uploaded the map back to the ECU to check... |
Forum: Induction 07-25-2012, 10:24 AM |
Replies: 16 Views: 16,940 |
Forum: Induction 07-04-2012, 09:47 AM |
Replies: 58 Views: 9,138 |
Forum: Induction 05-30-2012, 09:18 AM |
Replies: 5 Views: 1,297 |
Forum: Induction 05-30-2012, 09:17 AM |
Replies: 23 Views: 11,280 Looks different to my M44 bracket, as it has... Looks different to my M44 bracket, as it has three small holes on the LHS, although I know they changed the design. Wouldn't be too hard to make up your own bracket, and no need for a welded bung,... |
Forum: Induction 05-15-2012, 10:52 PM |
Replies: 5 Views: 1,297 Cheers John, I managed to get through to Metric... Cheers John, I managed to get through to Metric on the telephone and they sorted me out with them. The phone line was quite bad and I don't think they understood my English accent too well but they... |
Forum: Induction 05-14-2012, 04:39 PM |
Replies: 5 Views: 1,297 |
Forum: Induction 05-11-2012, 03:44 PM |
Replies: 15 Views: 3,739 |
Forum: Induction 05-10-2012, 09:41 PM |
Replies: 11 Views: 5,233 |
Forum: Induction 05-10-2012, 03:47 PM |
Replies: 5 Views: 1,297 Injector adapters Hi Where is the best place to get these? I have tried emailing Metric Mechanics but not luck so far. Will give them a call in a bit. Anywhere else? I see Vac Motorsports stock them, but at... |
Forum: Induction 05-10-2012, 12:55 PM |
Replies: 11 Views: 5,233 Which injectors for DASC mapping Hi, I want to upgrade from the RRFPR to bigger injectors and mapping. What injectors should I be using? I know I want a flow rate of around 30lb (315cc/min), with high impedance injectors. I guess... |
Forum: Induction 03-10-2012, 06:18 PM |
Replies: 0 Views: 695 Meth injection dribble Hi all Just been checking over my meth injection system and noticed that once the pump cuts off it dribbles for about 3 seconds. It is not a couple of drops but a full dribble. Is this normal? ... |
Forum: Induction 02-02-2012, 10:58 PM |
Replies: 27 Views: 5,166 They are rubbish anyway, go for some cam belt... They are rubbish anyway, go for some cam belt idler pulleys. The ones with double row ball bearings are the best. I got some off a Land Rover. Any will do as long as it has a flat face with a M10... |
Forum: Lounge 01-25-2012, 12:11 PM |
Replies: 94 Views: 29,693 Think it was the E30 M42 with no A/C that came... Think it was the E30 M42 with no A/C that came with single mass. My M44 compact with no A/C has dual mass. It is quite a small diameter though, so if you are going to put more power through it... |
Forum: Induction 11-16-2011, 01:32 PM |
Replies: 7 Views: 1,637 Yeah, stock RRFPR, stock injectors, M44 You... Yeah, stock RRFPR, stock injectors, M44 You can use the same belt as the auto tensioner will take up the excess slack, although it might then start to slip. Best to give it a go and see what... |
Forum: Induction 10-17-2011, 11:28 AM |
Replies: 7 Views: 1,637 Running 3.4" pulley feedback Just thought I would give my feedback on running the 3.4" pulley on my DASC with meth injection and standard RRFPR. Took it on a track day, ran it for the whole day, it got a bit warm and the... |
Forum: Transmission 11-03-2010, 04:31 PM |
Replies: 9 Views: 4,676 You can use a trolley jack, but trans jack much... You can use a trolley jack, but trans jack much better. Lots of 3/8 wobble bars and make sure you have the right torx sockets. The starter pin might get welded in making it a pain to get the trans... |
Forum: Exhausts 11-03-2010, 04:06 PM |
Replies: 17 Views: 4,346 Only the stock BMW exhaust is any good for... Only the stock BMW exhaust is any good for keeping it quiet in the UK. They are loads new so try and get a decent second hand one. They are worth their weight in gold in my opinion. They weigh... |
Forum: Differentials 10-28-2010, 06:49 PM |
Replies: 10 Views: 4,667 |
Forum: Differentials 10-27-2010, 10:23 PM |
Replies: 10 Views: 4,667 Will Z3 half shafts work? Hi guys Will Z3 2.8L half shafts work with an E30 medium case diff in a 318Ti? They have different part numbers to E30 half shafts, but this is probably because the pulse rings are plastic etc. ... |
Forum: Interior and ICE 10-27-2010, 01:37 PM |
Replies: 9 Views: 2,264 |
Forum: Induction 10-14-2010, 04:09 PM |
Replies: 15 Views: 5,374 |